Benito.txt 3 KB
Newer Older
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
/** \file
 *
 *  This file contains special DoxyGen information for the generation of the main page and other special
 *  documentation pages. It is not a project source file.
 */
 
/** \mainpage Benito Arduino Programmer Project
 *
 *  \section SSec_Compat Demo Compatibility:
 *
 *  The following table indicates what microcontrollers are compatible with this demo.
 *
 *  - AT90USB1287
 *  - AT90USB1286
 *  - AT90USB647
 *  - AT90USB646
 *  - ATMEGA32U6
 *  - ATMEGA32U4
 *  - ATMEGA16U4
 *  - AT90USB162
 *  - AT90USB82
 *
 *  \section SSec_Info USB Information:
 *
 *  The following table gives a rundown of the USB utilization of this demo.
 *
 * <table>
 *  <tr>
 *   <td><b>USB Mode:</b></td>
 *   <td>Device</td>
 *  </tr>
 *  <tr>
 *   <td><b>USB Class:</b></td>
 *   <td>Human Interface Device (HID)</td>
 *  </tr>
 *  <tr> 
 *   <td><b>USB Subclass:</b></td>
 *   <td>Keyboard</td>
 *  </tr>
 *  <tr>
 *   <td><b>Relevant Standards:</b></td>
 *   <td>USBIF HID Standard, USBIF HID Usage Tables</td>
 *  </tr>
 *  <tr>
 *   <td><b>Usable Speeds:</b></td>
 *   <td>Low Speed Mode, Full Speed Mode</td>
 *  </tr>
 * </table>
 *
 *  \section SSec_Description Project Description: 
 *
 *  Firmware for a USB AVR powered programmer for Arduino boards using the official Arduino bootloader. This
 *  project acts like a regular USB to Serial bridge, except that asserting the DTR line will cause a pulse
 *  to appear on a given port pin, to control the target's /RESET pin.
 *
 *  This is primarily designed to fit the Benito board from www.dorkbotpdx.org, but will suit all USB AVRs.
 *
 *  \section SSec_Options Project Options
 *
 *  The following defines can be found in this demo, which can control the demo behaviour when defined, or changed in value.
 *
 *  <table>
 *   <tr>
 *    <td><b>Define Name:</b></td>
 *    <td><b>Location:</b></td>
 *    <td><b>Description:</b></td>
 *   </tr>
 *   <tr>
 *    <td>AVR_RESET_LINE_PORT</td>
 *    <td>Makefile CDEFS</td>
 *    <td>Indicates the PORT register of the pin used to generate the target /RESET line pulse.</td>
 *   </tr>
 *   <tr>
 *    <td>AVR_RESET_LINE_DDR</td>
 *    <td>Makefile CDEFS</td>
 *    <td>Indicates the DDR register of the pin used to generate the target /RESET line pulse.</td>
 *   </tr>
 *   <tr>
 *    <td>AVR_RESET_LINE_MASK</td>
 *    <td>Makefile CDEFS</td>
 *    <td>Indicates the mask of the pin used to generate the target /RESET line pulse.</td>
 *   </tr>
 *   <tr>
 *    <td>AVR_RESET_PULSE_MS</td>
 *    <td>Makefile CDEFS</td>
 *    <td>Pulse length in milliseconds for the target /RESET pulse.</td>
 *   </tr>
 *   <tr>
 *    <td>TX_RX_LED_PULSE_MS</td>
 *    <td>Makefile CDEFS</td>
 *    <td>Pulse length in milliseconds for the activity Tx/Rx LEDs.</td>
 *   </tr>
93
94
95
96
97
 *   <tr>
 *    <td>PING_PONG_LED_PULSE_MS</td>
 *    <td>Makefile CDEFS</td>
 *    <td>Pulse length in milliseconds for the enumeration LED ping-poning between toggles.</td>
 *   </tr>
98
99
 *  </table>
 */