V2Protocol.c

/*
             LUFA Library
     Copyright (C) Dean Camera, 2009.
              
  dean [at] fourwalledcubicle [dot] com
      www.fourwalledcubicle.com
*/

/*
  Copyright 2009  Dean Camera (dean [at] fourwalledcubicle [dot] com)

  Permission to use, copy, modify, and distribute this software
  and its documentation for any purpose and without fee is hereby
  granted, provided that the above copyright notice appear in all
  copies and that both that the copyright notice and this
  permission notice and warranty disclaimer appear in supporting
  documentation, and that the name of the author not be used in
  advertising or publicity pertaining to distribution of the
  software without specific, written prior permission.

  The author disclaim all warranties with regard to this
  software, including all implied warranties of merchantability
  and fitness.  In no event shall the author be liable for any
  special, indirect or consequential damages or any damages
  whatsoever resulting from loss of use, data or profits, whether
  in an action of contract, negligence or other tortious action,
  arising out of or in connection with the use or performance of
  this software.
*/

/** \file
 *
 *  V2Protocol handler, to process V2 Protocol commands used in Atmel programmer devices.
 */

#define  INCLUDE_FROM_V2PROTOCOL_C
#include "V2Protocol.h"

/** Current memory address for FLASH/EEPROM memory read/write commands */
uint32_t CurrentAddress;

/** Flag to indicate that the next read/write operation must update the device's current address */
bool MustSetAddress;


/** ISR for the management of the command execution timeout counter */
ISR(TIMER0_COMPA_vect, ISR_BLOCK)
{
	if (TimeoutMSRemaining)
	  TimeoutMSRemaining--;
}

/** Master V2 Protocol packet handler, for received V2 Protocol packets from a connected host.
 *  This routine decodes the issued command and passes off the handling of the command to the
 *  appropriate function.
 */
void V2Protocol_ProcessCommand(void)
{
	uint8_t V2Command = Endpoint_Read_Byte();
	
	TimeoutMSRemaining = COMMAND_TIMEOUT_MS;
	TIMSK0 |= (1 << OCIE0A);

	switch (V2Command)
	{
		case CMD_SIGN_ON:
			V2Protocol_SignOn();
			break;
		case CMD_SET_PARAMETER:
		case CMD_GET_PARAMETER:
			V2Protocol_GetSetParam(V2Command);
			break;
		case CMD_LOAD_ADDRESS:
			V2Protocol_LoadAddress();
			break;
		case CMD_RESET_PROTECTION:
			V2Protocol_ResetProtection();
			break;
#if defined(ENABLE_ISP_PROTOCOL)
		case CMD_ENTER_PROGMODE_ISP:
			ISPProtocol_EnterISPMode();
			break;
		case CMD_LEAVE_PROGMODE_ISP:
			ISPProtocol_LeaveISPMode();
			break;
		case CMD_PROGRAM_FLASH_ISP:
		case CMD_PROGRAM_EEPROM_ISP:
			ISPProtocol_ProgramMemory(V2Command);			
			break;
		case CMD_READ_FLASH_ISP:
		case CMD_READ_EEPROM_ISP:
			ISPProtocol_ReadMemory(V2Command);
			break;
		case CMD_CHIP_ERASE_ISP:
			ISPProtocol_ChipErase();
			break;
		case CMD_READ_FUSE_ISP:
		case CMD_READ_LOCK_ISP:
		case CMD_READ_SIGNATURE_ISP:
		case CMD_READ_OSCCAL_ISP:
			ISPProtocol_ReadFuseLockSigOSCCAL(V2Command);
			break;
		case CMD_PROGRAM_FUSE_ISP:
		case CMD_PROGRAM_LOCK_ISP:
			ISPProtocol_WriteFuseLock(V2Command);
			break;
		case CMD_SPI_MULTI:
			ISPProtocol_SPIMulti();
			break;
#endif
#if defined(ENABLE_XPROG_PROTOCOL)
		case CMD_XPROG_SETMODE:
			XPROGProtocol_SetMode();
			break;
		case CMD_XPROG:
			XPROGProtocol_Command();
			break;
#endif
		default:
			V2Protocol_UnknownCommand(V2Command);
			break;
	}
		
	TIMSK0 &= ~(1 << OCIE0A);

	Endpoint_WaitUntilReady();
	Endpoint_SetEndpointDirection(ENDPOINT_DIR_OUT);
}

/** Handler for unknown V2 protocol commands. This discards all sent data and returns a
 *  STATUS_CMD_UNKNOWN status back to the host.
 *
 *  \param[in] V2Command  Issued V2 Protocol command byte from the host
 */
static void V2Protocol_UnknownCommand(const uint8_t V2Command)
{
	/* Discard all incoming data */
	while (Endpoint_BytesInEndpoint() == AVRISP_DATA_EPSIZE)
	{
		Endpoint_ClearOUT();
		Endpoint_WaitUntilReady();
	}

	Endpoint_ClearOUT();
	Endpoint_SetEndpointDirection(ENDPOINT_DIR_IN);

	Endpoint_Write_Byte(V2Command);
	Endpoint_Write_Byte(STATUS_CMD_UNKNOWN);
	Endpoint_ClearIN();
}

/** Handler for the CMD_SIGN_ON command, returning the programmer ID string to the host. */
static void V2Protocol_SignOn(void)
{
	Endpoint_ClearOUT();
	Endpoint_SetEndpointDirection(ENDPOINT_DIR_IN);

	Endpoint_Write_Byte(CMD_SIGN_ON);
	Endpoint_Write_Byte(STATUS_CMD_OK);
	Endpoint_Write_Byte(sizeof(PROGRAMMER_ID) - 1);
	Endpoint_Write_Stream_LE(PROGRAMMER_ID, (sizeof(PROGRAMMER_ID) - 1));
	Endpoint_ClearIN();
}

/** Handler for the CMD_RESET_PROTECTION command, currently implemented as a dummy ACK function
 *  as no ISP short-circuit protection is currently implemented.
 */
static void V2Protocol_ResetProtection(void)
{
	Endpoint_ClearOUT();
	Endpoint_SetEndpointDirection(ENDPOINT_DIR_IN);
	
	Endpoint_Write_Byte(CMD_RESET_PROTECTION);
	Endpoint_Write_Byte(STATUS_CMD_OK);
	Endpoint_ClearIN();	
}


/** Handler for the CMD_SET_PARAMETER and CMD_GET_PARAMETER commands from the host, setting or
 *  getting a device parameter's value from the parameter table.
 *
 *  \param[in] V2Command  Issued V2 Protocol command byte from the host
 */
static void V2Protocol_GetSetParam(const uint8_t V2Command)
{
	uint8_t ParamID = Endpoint_Read_Byte();
	uint8_t ParamValue;
	
	if (V2Command == CMD_SET_PARAMETER)
	  ParamValue = Endpoint_Read_Byte();

	Endpoint_ClearOUT();
	Endpoint_SetEndpointDirection(ENDPOINT_DIR_IN);
	
	Endpoint_Write_Byte(V2Command);
	
	uint8_t ParamPrivs = V2Params_GetParameterPrivileges(ParamID);
	
	if ((V2Command == CMD_SET_PARAMETER) && (ParamPrivs & PARAM_PRIV_WRITE))
	{
		Endpoint_Write_Byte(STATUS_CMD_OK);
		V2Params_SetParameterValue(ParamID, ParamValue);
	}
	else if ((V2Command == CMD_GET_PARAMETER) && (ParamPrivs & PARAM_PRIV_READ))
	{
		Endpoint_Write_Byte(STATUS_CMD_OK);
		Endpoint_Write_Byte(V2Params_GetParameterValue(ParamID));
	}
	else
	{	
		Endpoint_Write_Byte(STATUS_CMD_FAILED);
	}

	Endpoint_ClearIN();
}

/** Handler for the CMD_LOAD_ADDRESS command, loading the given device address into a
 *  global storage variable for later use, and issuing LOAD EXTENDED ADDRESS commands
 *  to the attached device as required.
 */
static void V2Protocol_LoadAddress(void)
{
	Endpoint_Read_Stream_BE(&CurrentAddress, sizeof(CurrentAddress));

	Endpoint_ClearOUT();
	Endpoint_SetEndpointDirection(ENDPOINT_DIR_IN);
	
	MustSetAddress = true;

	Endpoint_Write_Byte(CMD_LOAD_ADDRESS);
	Endpoint_Write_Byte(STATUS_CMD_OK);
	Endpoint_ClearIN();
}