TeensyHID.c 4.79 KB
Newer Older
1
2
3
4
5
6
7
8
9
10
11
/*
             LUFA Library
     Copyright (C) Dean Camera, 2009.
              
  dean [at] fourwalledcubicle [dot] com
      www.fourwalledcubicle.com
*/

/*
  Copyright 2009  Dean Camera (dean [at] fourwalledcubicle [dot] com)

12
13
14
15
16
17
18
  Permission to use, copy, modify, distribute, and sell this 
  software and its documentation for any purpose is hereby granted
  without fee, provided that the above copyright notice appear in 
  all copies and that both that the copyright notice and this
  permission notice and warranty disclaimer appear in supporting 
  documentation, and that the name of the author not be used in 
  advertising or publicity pertaining to distribution of the 
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
  software without specific, written prior permission.

  The author disclaim all warranties with regard to this
  software, including all implied warranties of merchantability
  and fitness.  In no event shall the author be liable for any
  special, indirect or consequential damages or any damages
  whatsoever resulting from loss of use, data or profits, whether
  in an action of contract, negligence or other tortious action,
  arising out of or in connection with the use or performance of
  this software.
*/

/** \file
 *
 *  Main source file for the TeensyHID bootloader. This file contains the complete bootloader logic.
 */
 
#include "TeensyHID.h"

/** Flag to indicate if the bootloader should be running, or should exit and allow the application code to run
 *  via a soft reset. When cleared, the bootloader will abort, the USB interface will shut down and the application
 *  started via a forced watchdog reset.
 */
bool RunBootloader = true;

/** Main program entry point. This routine configures the hardware required by the bootloader, then continuously 
 *  runs the bootloader processing routine until instructed to soft-exit.
 */
int main(void)
48
49
50
51
52
53
{
	/* Setup hardware required for the bootloader */
	SetupHardware();
	
	while (RunBootloader)
	  USB_USBTask();
54
	
55
56
	/* Disconnect from the host - USB interface will be reset later along with the AVR */
	USB_Detach();
57
58
59

	/* Enable the watchdog and force a timeout to reset the AVR */
	wdt_enable(WDTO_250MS);
60

61
62
63
64
65
	for (;;);
}

/** Configures all hardware required for the bootloader. */
void SetupHardware(void)
66
67
68
69
70
{
	/* Disable watchdog if enabled by bootloader/fuses */
	MCUSR &= ~(1 << WDRF);
	wdt_disable();

71
72
	/* Disable clock division */
	clock_prescale_set(clock_div_1);
73
74
75
76
77
78
79

	/* Relocate the interrupt vector table to the bootloader section */
	MCUCR = (1 << IVCE);
	MCUCR = (1 << IVSEL);

	/* Initialize USB subsystem */
	USB_Init();
80
}
81
82
83
84

/** Event handler for the USB_ConfigurationChanged event. This configures the device's endpoints ready
 *  to relay data to and from the attached USB host.
 */
85
void EVENT_USB_Device_ConfigurationChanged(void)
86
87
88
89
90
91
92
{
	/* Setup HID Report Endpoint */
	Endpoint_ConfigureEndpoint(HID_EPNUM, EP_TYPE_INTERRUPT,
		                       ENDPOINT_DIR_IN, HID_EPSIZE,
	                           ENDPOINT_BANK_SINGLE);
}

93
/** Event handler for the USB_UnhandledControlRequest event. This is used to catch standard and class specific
94
95
96
 *  control requests that are not handled internally by the USB library (including the HID commands, which are
 *  all issued via the control endpoint), so that they can be handled appropriately for the application.
 */
97
void EVENT_USB_Device_UnhandledControlRequest(void)
98
99
{
	/* Handle HID Class specific requests */
100
	switch (USB_ControlRequest.bRequest)
101
102
	{
		case REQ_SetReport:
103
			Endpoint_ClearSETUP();
104
			
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
			/* Wait until the command has been sent by the host */
			while (!(Endpoint_IsOUTReceived()));
		
			/* Read in the write destination address */
			uint16_t PageAddress = Endpoint_Read_Word_LE();
			
			/* Check if the command is a program page command, or a start application command */
			if (PageAddress == TEENSY_STARTAPPLICATION)
			{
				RunBootloader = false;
			}
			else
			{
				/* Erase the given FLASH page, ready to be programmed */
				boot_page_erase(PageAddress);
				boot_spm_busy_wait();
121
				
122
123
				/* Write each of the FLASH page's bytes in sequence */
				for (uint8_t PageByte = 0; PageByte < SPM_PAGESIZE; PageByte += 2)
124
				{
125
126
					/* Check if endpoint is empty - if so clear it and wait until ready for next packet */
					if (!(Endpoint_BytesInEndpoint()))
127
					{
128
129
						Endpoint_ClearOUT();
						while (!(Endpoint_IsOUTReceived()));
130
131
					}

132
133
					/* Write the next data word to the FLASH page */
					boot_page_fill(PageAddress + PageByte, Endpoint_Read_Word_LE());
134
135
				}

136
137
138
				/* Write the filled FLASH page to memory */
				boot_page_write(PageAddress);
				boot_spm_busy_wait();
139

140
141
				/* Re-enable RWW section */
				boot_rww_enable();
142
			}
143
144
145
146

			Endpoint_ClearOUT();

			Endpoint_ClearStatusStage();
147
148
149
150
			
			break;
	}
}