GitLab

Fixed incorrect PollingIntervalMS values in the demo/project/bootloader endpoint descriptors (thanks to MCS Electronics).

Fixed calculation of timer register reload values derived from F_CPU; must subtract one from the division result for the compare value to be correct.

Change AVRISP-MKII rescue clock speed to 4MHz to ensure that a 125KHz ISP speed works regardless of the target's fuses (i.e. DIV8 set).

Renamed the EVENT_USB_Device_UnhandledControlRequest() event to EVENT_USB_Device_ControlRequest() as it is now fired before the library request handlers, not afterwards.

Fixed USBtoSerial and XPLAINBridge demos discarding data from the PC if the send buffer becomes full.

Fixed MIDI class driver send routines silently discarding packets if the endpoint or pipe is busy (thanks to Robin Green).

Rescue clock of the AVRISP-MKII moved to the AVR's OCR1A pin, so that the clock can be generated at all times when 125KHz ISP programming mode is selected.

Rename new CDC class bootloader NO_LOCK_BYTE_SUPPORT compile time option to NO_LOCK_BYTE_WRITE_SUPPORT as reads are still permitted.

Clean up CDC bootloader command processing code.

Added new NO_BLOCK_SUPPORT, NO_EEPROM_BYTE_SUPPORT, NO_FLASH_BYTE_SUPPORT and NO_LOCK_BYTE_SUPPORT compile time options to the CDC class bootloader.

Added new NO_CLASS_DRIVER_AUTOFLUSH compile time option to disable automatic flushing of interfaces when the USB management tasks for each driver is called.

The MIDI class drivers now automatically flushes the MIDI interface when the MIDI class driver's USBTask() function is called.

Changed AudioInput and AudioOutput demos to reload the next sample via an interrupt rather than polling the sample timer.

All USB class drivers are now automatically included when LUFA/Drivers/USB.h is included, and no longer need to be seperately included.

All LowLevel demos changed to use the constants and types defined in the USB class drivers.

Renamed ENDPOINT_DOUBLEBANK_SUPPORTED() to ENDPOINT_BANKS_SUPPORTED() and changed it to return the maximum number of supported banks for the given endpoint.

Fixed MIDI_Host_Flush() not aborting early when the specified MIDI host interface was not configured.

Small documentation improvements to explicitly reference tokens in Doxygen, to ensure that they are converted to cross-reference links in the output files.

Moved the USB device selection logic for ENDPOINT_TOTAL_ENDPOINTS further up in Endpoint.h to where the endpoint bank capabilities are determined, to reduce the total number of device-specific logic.

Change USB_Host_WaitMS() to test and disable the HSOFI interrupt before resuming the bus, so that it does not fire before the delay loop has run.

Add missing const qualifier to the parameter of USB_Host_ClearPipeStall().

Fixed random enumeration failure while in device mode due to interrupts causing the Set Address request to exceed maximum timings.

Added SVN eol-style property to the library driver files that are missing it.

Cache the USB_DeviceState variable internally in the library core when multiple checks are required in a single loop iteration, to reduce compiled code size.

Revert change to the AVRISP-MKII project for fuse byte programming via the CMDEX bit - this appears to be an error in the XMEGA manual external memory programming table.

Fixed broken FLASH/EEPROM programming in the AVRISP-MKII clone project when writing in non-paged mode and the polling byte cannot be used.

Fix low level host mode demos not correctly fetching the next endpoint when an invalid interface is discarded.

Update the pipe configuration routines in the host mode class drivers so that they use the same new code to enumerate compatible devices to increase reliability. Add support to the host mode class drivers for non-sequential (but non-overlapping with other interface) pipe numbers.

Reverted Endpoint/Pipe non-sequential configuration hack, placed restriction on the configuration order instead to ensure maximum reliability.

Altered all low level device and host mode demos to ensure that endpoints and pipes are configured in ascending order properly.

Rewrote all low level host mode demos' configuration descriptor parser code to ensure that pipes are enumerated in ascending order, and to ensure maximum compatibility with devices.

Incremented all device mode demo's device descriptor revision numbers to ensure that any descriptor changes are re-fetched on machines which have enumerated previous versions.

Changed default value for the reset polarity parameter in the AVRISP-MKII project so that it defaults to active low drive.

Fixed incorrect USB_DeviceState value when unconfiguring the device without an address set.

Fixed incorrect LEDs_ChangeLEDs() function in the Benito board LED driver.

Added CDC functional descriptor structs to the Low Level CDC demos and CDC class bootloader, to improve the readability of the descriptors.

Fixed BootloaderCDC project failing on some operating systems due to removed Line Encoding options (thanks to Alexey Belyaev).

Add new CDC descriptor structs to the CDC class driver, so that the CDC demos can use human readable field names.

Rename prefix for Still Image Host class driver functions from "SImage_" to "SI_" to remain consistent with the rest of the driver.

Remove dfu-programmer program switches, to ensure maximum compatibility with all dfu-programmer versions.

Added the --suppress-bootloader-mem option to the makefile dfu target, to ensure that writes to the bootloader section of the AVR's flash memory are ignored (thanks to Axel Rohde).

Fixed incorrect command name for EEPROM memory programming in the makefile dfu-ee target.

Makefile whitespace fixes.

Fixed endpoint selection within the CALLBACK_HID_Device_CreateHIDReport() callback function causing broken GET REPORT requests.

Minor whitespace fixes.

Fixed SUSPI interrupt not being cleared during device mode enumeration, causing accidental mis-fires on re-enumeration.

Fixed JTAG_DEBUG_POINT() and JTAG_DEBUG_BREAK() macros not compiling under pure C99 standards mode.