USB_Init() no longer calls sei() to enable global interrupts - this must now be done in the user application once all init code has run.

Removed two-step endpoint/pipe bank clear and switch sequence for smaller, faster endpoint/pipe code.

Added spacing between multiple paragraphs in Doxygen \note sections.

Removed call to the clock prescaler reset function in the Teensy bootloader to save space - the user application is accessed via a watchdog reset anyway, so the prescale reset would only affect the speed of the bootloader itself.

Make sure that USB_STREAM_TIMEOUT_MS is set in the MassStorageHost ClassDriver demo, so that slow devices don't time out the data pipe. Increase pipe timeout in both MassStorageHost demos to 5 seconds to account for the really slow devices.

Fix TeensyHID bootloader not properly shutting down the USB interface to trigger a disconnection on the host before resetting the AVR.

Renamed all library events to properly seperate out Device and Host mode events. Changed the firing conditions for some events to ensure that events are fired by their own USB mode only.

Remove VBUS events - not needed as the library takes care of VBUS detection and feedback on supported AVRs via the USB_Device_Connected and USB_Device_Disconnected events.

Fixed incorrect Host state assignment in the incomplete BluetoothHost demo.

Renamed USB_Device_SetHighSpeed() to USB_Device_SetFullSpeed() so that the correct terminology is used (thanks to Brian Dickman).

Fix USB_PLL_Off() call in the series 4, 6 and 7 microcontroller disconnect interrupt handler code, which wasn't guarded by a test of USB_Options to check if the user has specified manual PLL control (thanks to Brian Dickman).

Changed USB_Init() and USB_Shutdown() so that they are no longer dependant on oneanother for possible code savings when the interface is never explicitly shut down.

Added new Endpoint_ClearStatusStage() convenience function to assist with the status stages of control transfers.

Removed vague USB_IsConnected global - test USB_DeviceState or USB_HostState explicitly to gain previous functionality.

Removed USB_IsSuspended global - test USB_DeviceState against DEVICE_STATE_Suspended instead.

Fixed possible enumeration errors from spinloops which may fail to exit if the USB connection is severed before the exit condition becomes true.

Updated bootloaders to use the new main() function layout and remove any references to the scheduler to keep them in line with the rest of the library.

Fixed incorrect ENDPOINT_EPNUM_MASK mask preventing endpoints above EP3 from being selected (thanks to Jonathan Oakley).

Removed STREAM_CALLBACK() macro - callbacks now use regular function definitions to clarify user code.

Removed DESCRIPTOR_COMPARATOR() macro - comparators should now use regular function definitions to clarify user code.

USB_HostRequest renamed to USB_ControlRequest, entire control request header is now read into USB_ControlRequest in Device mode rather than having the library pass only partially read header data to the application.

The USB_UnhandledControlPacket event has had its parameters removed, in favour of accessing the new USB_ControlRequest structure.

The Endpoint control stream functions now correctly send a ZLP to the host when less data than requested is sent.

Removed specialized Endpoint_ClearControl* and Pipe_ClearControl* macros in favour of the standard Endpoint_Clear* and Pipe_Clear* macros (Atmel have confirmed no effect from setting FIFOCON on control endpoints).

Fixed GenericHIDHost demo report write routine incorrect for control type requests (thanks to Andrei Krainev).

Removed Endpoint_ClearCurrentBank() and Pipe_ClearCurrentBank() in favour of new Endpoint_ClearIN(), Endpoint_ClearOUT(), Endpoint_ClearControlIN(), Endpoint_ClearControlOUT(), Pipe_ClearIN(), Pipe_ClearOUT(), Pipe_ClearControlIN() and Pipe_ClearControlOUT() macros (done to allow for the detection of packets of zero length).

Renamed *_ReadWriteAllowed() macros to *_IsReadWriteAllowed() to remain consistent with the rest of the LUFA API.

Endpoint_IsSetupReceived() macro has been renamed to Endpoint_IsSETUPReceived(), Endpoint_ClearSetupReceived() macro has been renamed to Endpoint_ClearControlSETUP(), the Pipe_IsSetupSent() macro has been renamed to Pipe_IsSETUPSent() and the Pipe_ClearSetupSent() macro is no longer applicable and should be removed - changes made to compliment the new endpoint and pipe bank management API.

Updated all demos, bootloaders and projects to use the new endpoint and pipe management APIs (thanks to Roman Thiel).

Updated library doxygen documentation, added groups, changed documentation macro functions to real functions for clarity.

Removed old endpoint and pipe aliased read/write/discard routines which did not have an explicit endian specifier for clarity.

Removed the ButtLoadTag.h header file, as no one used for its intended purpose anyway.

Fixed incorrect/missing control status stage transfers on demos, bootloaders and applications (thanks to Nate Lawson).