Removed the stream example code from the Low Level VirtualSerial demos, as...

Removed the stream example code from the Low Level VirtualSerial demos, as they were buggy and only served to add clutter.

Demos/Device/LowLevel/VirtualSerial/VirtualSerial.c

@@ -49,59 +49,6 @@ CDC_Line_Coding_t LineEncoding = { .BaudRateBPS = 0,
                                    .ParityType  = Parity_None,
                                    .DataBits    = 8            };
 
-
-#if 0
-/* NOTE: Here you can set up a standard stream using the created virtual serial port, so that the standard stream functions in
- *       <stdio.h> can be used on the virtual serial port (e.g. fprintf(&USBSerial, "Test"); to print a string).
- */
-	
-static int CDC_putchar(char c, FILE *stream)
-{	  
-	Endpoint_SelectEndpoint(CDC_TX_EPNUM);
-
-	if (!(LineEncoding.BaudRateBPS))
-	  return -1;
-	
-	if (Endpoint_WaitUntilReady())
-	  return -1;
-
-	Endpoint_Write_Byte(c);
-	Endpoint_ClearIN();
-	
-	return 0;
-}
-
-static int CDC_getchar(FILE *stream)
-{
-	int c;
-
-	if (!(LineEncoding.BaudRateBPS))
-	  return -1;
-
-	Endpoint_SelectEndpoint(CDC_RX_EPNUM);
-	
-	for (;;)
-	{
-		if (Endpoint_WaitUntilReady())
-		  return -1;
-	
-		if (!(Endpoint_BytesInEndpoint()))
-		{
-			Endpoint_ClearOUT();
-		}
-		else
-		{
-			c = Endpoint_Read_Byte();
-			break;
-		}
-	}
-	
-	return c;
-}
-
-static FILE USBSerial = FDEV_SETUP_STREAM(CDC_putchar, CDC_getchar, _FDEV_SETUP_RW);
-#endif
-
 /** Main program entry point. This routine contains the overall program flow, including initial
  *  setup of all components and the main program loop.
  */

Demos/Host/LowLevel/VirtualSerialHost/VirtualSerialHost.c

@@ -36,52 +36,6 @@
  
 #include "VirtualSerialHost.h"
 
-#if 0
-/* NOTE: Here you can set up a standard stream using the created virtual serial port, so that the standard stream functions in
- *       <stdio.h> can be used on the virtual serial port (e.g. fprintf(&USBSerial, "Test"); to print a string).
- */
-	
-static int CDC_putchar(char c, FILE *stream)
-{	  
-	Pipe_SelectPipe(CDC_DATAPIPE_OUT);
-	
-	if (Pipe_WaitUntilReady())
-	  return -1;
-
-	Pipe_Write_Byte(c);
-	Pipe_ClearIN();
-	
-	return 0;
-}
-
-static int CDC_getchar(FILE *stream)
-{
-	int c;
-
-	Pipe_SelectPipe(CDC_DATAPIPE_IN);
-	
-	for (;;)
-	{
-		if (Pipe_WaitUntilReady())
-		  return -1;
-	
-		if (!(Pipe_BytesInPipe()))
-		{
-			Pipe_ClearOUT();
-		}
-		else
-		{
-			c = Pipe_Read_Byte();
-			break;
-		}
-	}
-	
-	return c;
-}
-
-static FILE USBSerial = FDEV_SETUP_STREAM(CDC_putchar, CDC_getchar, _FDEV_SETUP_RW);
-#endif
-
 /** Main program entry point. This routine configures the hardware required by the application, then
  *  enters a loop to run the application tasks in sequence.
  */

LUFA/ManPages/ChangeLog.txt

@@ -32,6 +32,7 @@
   *  - Inlined currently unused (but standardized) maintenance functions in the Device and Host Class drivers to save space
   *  - The XPLAINBridge project now selects between a USB to Serial bridge and a PDI programmer on startup, reading the JTAG port's
   *    TDI pin to determine which mode to use
+  *  - Removed the stream example code from the Low Level VirtualSerial demos, as they were buggy and only served to add clutter
   *
   *  <b>Fixed:</b>
   *  - Fixed AVRISP project not able to enter programming mode when ISP protocol is used