Fixed incorrect definition of the HID_KEYBOARD_SC_D constant in the HID class driver (thanks to Opendous Inc.).

Add extra comments to the ISPTarget.c source file in the AVRISP-MKII clone project.

Fixed possible lost data in the XPLAINBridge, USBtoSerial and Benito projects when the host exceeds the packet timeout period on received packets as set by USB_STREAM_TIMEOUT_MS (thanks to Justin Rajewski).

Changed the XPLAINBridge software UART to use the regular CTC mode instead of the alternative CTC mode via the Input Capture register, to reduce user confusion.

Make the incomplete MIDIToneGenerator project work with up to three notes, using a LRU (Least Recently Used) algorithm to discard the oldest set note when the note table becomes full.

Readd incomplete MIDIToneGenerator project, which can now correctly generate up to three simultaneous notes from MIDI channel 0.

Fixed Benito project discarding incoming data from the USB virtual serial port when the USART is busy.

Minor documentation improvements.

Lower bulk endpoint polling rate in the descriptors to the lowest possible value to give maximum throughput.

Oops - reduce size of each ring buffer in the USBtoSerial and Benito projects so that the RAM is not overflowed on the smaller USB AVR targets (thanks to Andrei from Microsin.ru).

Rename incorrectly named XPROGTarget_SendBreak() function to XPROGTarget_SendIdle(), as it is sending idle bits and not break bits.

Fixed AVRISP-MKII clone project not starting the target's program automatically after exiting TPI programming mode.

Slow AVRISP-MKII clone PDI/TPI programming speed back to 250KHz due to issues with the XPLAINBridge when PDI programming at faster rates.

Speed up XMEGANVM_WaitWhileNVMControllerBusy() by preloading the status register address into the pointer register of the target's NVM controller and then reading via a faster indirect load command.

Added new XCK_RESCUE_CLOCK_ENABLE compile time option to the AVRISP-MKII clone programmer project (thanks to Tom Light).

Fixed PDI/TPI programming speed of ~250KHz in the AVRISP-MKII Clone project, instead of the desired 500KHz.

Fixed incorrect PollingIntervalMS values in the demo/project/bootloader endpoint descriptors (thanks to MCS Electronics).

Fixed calculation of timer register reload values derived from F_CPU; must subtract one from the division result for the compare value to be correct.

Change AVRISP-MKII rescue clock speed to 4MHz to ensure that a 125KHz ISP speed works regardless of the target's fuses (i.e. DIV8 set).

Renamed the EVENT_USB_Device_UnhandledControlRequest() event to EVENT_USB_Device_ControlRequest() as it is now fired before the library request handlers, not afterwards.

Fixed USBtoSerial and XPLAINBridge demos discarding data from the PC if the send buffer becomes full.

Fix XPLAINBridge code broken during the changes to the Rescue Clock generation in the AVRISP-MKII clone project.

Change over all low level host mode project's descriptor comparator routines to perform the descriptor casting in a temp variable to make the code clearer and easier to modify (despite being more verbose).

Rescue clock of the AVRISP-MKII moved to the AVR's OCR1A pin, so that the clock can be generated at all times when 125KHz ISP programming mode is selected.

Changed over www.fourwalledcubicle.com links to the new www.lufa-lib.org redirect domain, including the new aliased links for LUFA-related pages such as the various download/source control mirrors and support lists.

Add descriptor class, subclass and protocol constants to the class drivers, modify all demos to use them where possible.

Move out private/internal host class driver constants to the common class driver headers, so that they can be used in the Low Level host mode demos.

Ensure all demos, projects and bootloaders use the class driver constants where possible to minimise code repetition.

All USB class drivers are now automatically included when LUFA/Drivers/USB.h is included, and no longer need to be seperately included.

All LowLevel demos changed to use the constants and types defined in the USB class drivers.

Fix incomplete StandaloneProgrammer project code not compiling due to the recent API changes in the LUFA core.

Fix SoftUART.c not compiling due to accidental check in of changes not yet complete in the rest of the XPLAINBridge project code.

Fix Webserver project code not compiling due to the changes to the USB mode selection constant names.

Fixed ISR definition conflict in the XPLAIN bridge between the software UART and the AVRISP-MKII ISP modules.

Revert change to the AVRISP-MKII project for fuse byte programming via the CMDEX bit - this appears to be an error in the XMEGA manual external memory programming table.

Fixed broken FLASH/EEPROM programming in the AVRISP-MKII clone project when writing in non-paged mode and the polling byte cannot be used.