Fixed issue in USBtoSerial demos where the USART Rx line was not having its pullup enabled at startup, leading to noise being received from the Rx pin when left floating.

Removed unused relative Common.h header include from the DriverStubs board stub drivers.

Fixed Benito programmer, use the correct LED functions where needed to ensure correct status display at all times.

Renamed all library events to properly seperate out Device and Host mode events. Changed the firing conditions for some events to ensure that events are fired by their own USB mode only.

Remove VBUS events - not needed as the library takes care of VBUS detection and feedback on supported AVRs via the USB_Device_Connected and USB_Device_Disconnected events.

Fixed incorrect Host state assignment in the incomplete BluetoothHost demo.

Rename TOTAL_NUM_CONFIGURATIONS to FIXED_NUM_CONFIGURATIONS, to match the existing FIXED_CONTROL_ENDPOINT_SIZE compile time option. Add FIXED_NUM_CONFIGURATIONS to the descriptors of each project using the option.

Renamed USB_Device_SetHighSpeed() to USB_Device_SetFullSpeed() so that the correct terminology is used (thanks to Brian Dickman).

Fix USB_PLL_Off() call in the series 4, 6 and 7 microcontroller disconnect interrupt handler code, which wasn't guarded by a test of USB_Options to check if the user has specified manual PLL control (thanks to Brian Dickman).

Change project makefiles so that the current target settings and not just the board selection is printed during the build process.

Fix warning in AudioOutput demos when AUDIO_OUT_STEREO output mode is selected.

Better solution - change compile time token names to DEVICE_STATE_AS_GPIOR and HOST_STATE_AS_GPIOR and allow the user to set them to the index of the GPIOR register within the device to use.

Added HOST_STATE_AS_GPIOR1 and DEVICE_STATE_AS_GPIOR0 compile time options, the latter of which is used in the bootloaders, to reduce code size.

Added new Benito project, a simple modified USB-to-Serial bridge for the programming of AVRs using the official Arduino bootloader.

Ensure that the USB_DeviceState variable is properly set upon wakeup events, to the Addressed or Configured state as needed.

Add explicit support for the AT90USB646 to the Teensy bootloader now that PJRC have released the Teensy++ board.

Ensure unfinished SideShow demo uses an unallocated PID value within the LUFA range.

Changed USB_Init() and USB_Shutdown() so that they are no longer dependant on oneanother for possible code savings when the interface is never explicitly shut down.

Added new Endpoint_ClearStatusStage() convenience function to assist with the status stages of control transfers.

Removed vague USB_IsConnected global - test USB_DeviceState or USB_HostState explicitly to gain previous functionality.

Removed USB_IsSuspended global - test USB_DeviceState against DEVICE_STATE_Suspended instead.

Fixed possible enumeration errors from spinloops which may fail to exit if the USB connection is severed before the exit condition becomes true.

Change Doxygen configuration files to not produce 4096 directories for the documentation files -- the LUFA components do not generate enough documentation files to justify the large performance hit of creating so many directories.

Fix missing Doxygen documentation in the Class Driver Mass Storage Device demo.

Added new TOTAL_NUM_CONFIGURATIONS option, removed USE_SINGLE_DEVICE_CONFIGURATION compile time option (but silently convert it to USE_SINGLE_DEVICE_CONFIGURATION internally for compatibility).

Added new USE_FLASH_DESCRIPTORS compile time option. By default, descriptors can now lie in mixed memory spaces (specified by a new parameter to the CALLBACK_USB_GetDescriptor() function) unless one of the USE_*_DESCRIPTORS compile time option is specified.

Documented FAST_STREAM_TRANSFERS compile time option.

Reduced the TCP window size for the RNDIS demos (Class and LowLevel) to make them compatible with the AT90USB64x.

Seperated out Lib components of the incomplete BluetoothHost demo application out into a seperate Lib subfolder.

Changed F_CLOCK entries in project makefiles to alias to F_CPU by default, as this is the most common case.

Added parameter directions to function parameter documentation.

Added new experimental FAST_STREAM_FUNCTIONS compile time option to speed up stream transfers at the expense of a higher FLASH consumption (needs testing to verify improved throughput).

Remove all Host mode class demos other than the CDCHost class driver demo, so that they can be re-added as they are made once the host mode class framework is designed.

Fixed USB_Host_SendControlRequest() not re-suspending the USB bus when initial device ready-wait fails.

Fixed USB Pad regulator not being disabled on some AVR models when the USB_OPT_REG_DISABLED option is used.

Add NO_INTERNAL_SERIAL compile time option to bootloaders to prevent them from having unneccesary size increases from unused code.

Re-add signature byte defines to the DFU and CDC class bootloaders -- the SIGNATURE_x defines in the AVR device header files only exist in a newer version of avr-libc than is in the Debian repositories, causing build issues on Linux.

Fix makefiles -- the auto-addition of -D switches to each LUFA compile time option was faulty, due to GNUMake becomming confused by the spaces in the USE_STATIC_OPTIONS lines. Make user add in the switches explicitly instead.

Added new USB_Host_ClearPipeStall() convenience function to clear a stall condition on an attached device's endpoint.

Added new USB_Host_GetDeviceDescriptor() convenience function to retrieve the attached device's Device descriptor.

Make Pipe_ConfigurePipe() mask the given endpoint number against PIPE_EPNUM_MASK to ensure the endpoint IN direction bit is cleared to prevent endpoint type corruption.

Fix documentation mentioning Pipe_GetCurrentToken() function when real name is Pipe_GetPipeToken().

Better documentation for the MissleLauncher project - add credit to PyLauncher project.

Updated bootloaders to use the new main() function layout and remove any references to the scheduler to keep them in line with the rest of the library.

Converted Host mode demos to schedulerless. Fixed host mode broken due to earlier Start-of-frame event experiments.

Remove outdated AVRStudio project files from demos, projects, bootloaders. Fix makefiles of ClassDriver device demos.

Redocumented all device demos, now that they have changed over to the new USB class drivers.

Added C linkage to class drivers for C++ support.

Added prefixes to most of the class driver constants to prevent name clashes.

Commit of new class abstraction APIs for all device demos other than the MIDI demo - not documented yet.

Removed scheduler and memory allocation libraries.

Added new EVENT_USB_StartOfFrame event in the library to indicate the start of each USB frame (when generated).

Removed Tx interrupt from the USBtoSerial demo; now sends characters via polling to ensure more time for the Rx interrupt.

Change USBtoSerial Tx to polling-driven rather than interrupt driven, to ensure more time for the Rx interrupt to be serviced.

Deleted StdDescriptors.c, renamed USB_GetDescriptor() to CALLBACK_USB_GetDescriptor, moved ConfigDescriptor.c/.h from the LUFA/Drivers/USB/Class/ directory to LUFA/Drivers/USB/HighLevel/ in preperation for the new USB class APIs.

Fixed incorrect ENDPOINT_EPNUM_MASK mask preventing endpoints above EP3 from being selected (thanks to Jonathan Oakley).

Removed STREAM_CALLBACK() macro - callbacks now use regular function definitions to clarify user code.

Removed DESCRIPTOR_COMPARATOR() macro - comparators should now use regular function definitions to clarify user code.

Renamed the the TotalHIDReports element of the HID descriptor structure in the HID class demos to TotalReportDescriptors, to be more accurate of the element's function (thanks to Brian Dickman).

Changed PIPE_CONTROLPIPE_DEFAULT_SIZE from 8 to 64 to try to prevent problems with faulty devices which do not respect the given wLength value when reading in the device descriptor.

Further documentation improvements - removed file view from the main library documentation, replaced file references in the documentation with group references.

Fixed Endpoint_Write_Control_* functions writing more data than expected by the host, causing it to panic (thanks to Johannes Raschke).

Endpoint configuration is now refined to give better output when all configurations have static inputs - removed the now useless STATIC_ENDPOINT_CONFIGURATION compile time token.