Add svn:eol-style property to source files, so that the line endings are correctly converted to the target system's native end of line style.

Don't cast the line encoding baud rate to a uint16_t before performing the baud rate calculation in the Benito project.

USB_Init() no longer calls sei() to enable global interrupts - this must now be done in the user application once all init code has run.

Add double banking property to LUFA powered projects in the Projects directory. Add guards to macro parameters to ensure that formulas passed as parameters don't mess up the internal macro structure.

Updated Benito project -- added hardware interrupt and software buffering for serial data reception to prevent missed characters, condensed pulse generation counters into a struct for clarity.

Added check to CDC_Device_BytesReceived() to ensure 0 is returned when device is not enumerated to a host.

Move AVRISP project's V2Protocol_DelayMS() function to be static inline, as it is now very minimal. Added extra project doxygen documentation.

Added new Endpoint_SetEndpointDirection() macro to set the current endpoint direction for bidirectional endpoints.

Renamed internal USB_INT_ENDPOINT_SETUP macro to USB_INT_RXSTPI to fit in with the rest of the interrupt vector macros.

Make Benito ping-pong LED code more explicit, using masks of the TX and RX LED masks for ping-pong toggle rather than the ambiguous LED "Busy" mask.

Fix incorrect event name in MassStorageHost.c.

Fixed issue in USBtoSerial demos where the USART Rx line was not having its pullup enabled at startup, leading to noise being received from the Rx pin when left floating.

Removed unused relative Common.h header include from the DriverStubs board stub drivers.

Fixed Benito programmer, use the correct LED functions where needed to ensure correct status display at all times.

Renamed all library events to properly seperate out Device and Host mode events. Changed the firing conditions for some events to ensure that events are fired by their own USB mode only.

Remove VBUS events - not needed as the library takes care of VBUS detection and feedback on supported AVRs via the USB_Device_Connected and USB_Device_Disconnected events.

Fixed incorrect Host state assignment in the incomplete BluetoothHost demo.

Changed AudioOutput demos to explicitly use timer 3 - the smaller USB AVRs where timer 1 was needed instead did not have the endpoint size neccesary for good audio throughput anyway.

Fix Benito documentation indicating erronously that the project used the HID USB class instead of the CDC class.

State information for class drivers is now zeroed out during enumeration (both in device and host mode) to ensure sane values after each enumeration. User code should no longer explicitly set state information as this is no longer preserved.

Ensure new Benito Programmer project matches Don's established LED behaviour - flash LED while generating target /RESET pulse, ping-pong LEDs during enumeration.

Added new Benito project, a simple modified USB-to-Serial bridge for the programming of AVRs using the official Arduino bootloader.

Added new Endpoint_ClearStatusStage() convenience function to assist with the status stages of control transfers.

Removed vague USB_IsConnected global - test USB_DeviceState or USB_HostState explicitly to gain previous functionality.

Removed USB_IsSuspended global - test USB_DeviceState against DEVICE_STATE_Suspended instead.

Fixed possible enumeration errors from spinloops which may fail to exit if the USB connection is severed before the exit condition becomes true.

Added parameter directions to function parameter documentation.

Added new experimental FAST_STREAM_FUNCTIONS compile time option to speed up stream transfers at the expense of a higher FLASH consumption (needs testing to verify improved throughput).

Break device mode class driver interfaces into seperate config and state structs which are then combined, for clarity. Move device mode class driver interfaces back into the device mode class driver headers from the common class headers to make room for host class interfaces.

Changed to new device mode Class Driver function name prefixes to make way for similar host mode Class drivers.

Move new Class Driver powered demos to a new ClassDriver subdirectory, re-add old low level demos to a LowLevel subdirectory.

Redocumented all device demos, now that they have changed over to the new USB class drivers.

Added C linkage to class drivers for C++ support.

Added prefixes to most of the class driver constants to prevent name clashes.

Commit of new class abstraction APIs for all device demos other than the MIDI demo - not documented yet.

Removed scheduler and memory allocation libraries.

Added new EVENT_USB_StartOfFrame event in the library to indicate the start of each USB frame (when generated).

Removed Tx interrupt from the USBtoSerial demo; now sends characters via polling to ensure more time for the Rx interrupt.

Change USBtoSerial Tx to polling-driven rather than interrupt driven, to ensure more time for the Rx interrupt to be serviced.

Fixed incorrect ENDPOINT_EPNUM_MASK mask preventing endpoints above EP3 from being selected (thanks to Jonathan Oakley).

Removed STREAM_CALLBACK() macro - callbacks now use regular function definitions to clarify user code.

Removed DESCRIPTOR_COMPARATOR() macro - comparators should now use regular function definitions to clarify user code.

Fixed USB_RemoteWakeupEnabled flag never being set (the REMOTE WAKEUP Set Feature request was not being handled).

Renamed the FEATURELESS_CONTROL_ONLY_DEVICE compile-time token to CONTROL_ONLY_DEVICE.

USB_HostRequest renamed to USB_ControlRequest, entire control request header is now read into USB_ControlRequest in Device mode rather than having the library pass only partially read header data to the application.

The USB_UnhandledControlPacket event has had its parameters removed, in favour of accessing the new USB_ControlRequest structure.

The Endpoint control stream functions now correctly send a ZLP to the host when less data than requested is sent.

Removed specialized Endpoint_ClearControl* and Pipe_ClearControl* macros in favour of the standard Endpoint_Clear* and Pipe_Clear* macros (Atmel have confirmed no effect from setting FIFOCON on control endpoints).

Changed over all deprecated GCC structure tag initializers to the standardized C99 format (thanks to Mike Alexander).

Fixed CDC and USBtoSerial demos freezing where buffers were full while still transmitting or receiving (thanks to Peter Hand).

Fixed GenericHIDHost demo report write routine incorrect for control type requests (thanks to Andrei Krainev).

Removed Endpoint_ClearCurrentBank() and Pipe_ClearCurrentBank() in favour of new Endpoint_ClearIN(), Endpoint_ClearOUT(), Endpoint_ClearControlIN(), Endpoint_ClearControlOUT(), Pipe_ClearIN(), Pipe_ClearOUT(), Pipe_ClearControlIN() and Pipe_ClearControlOUT() macros (done to allow for the detection of packets of zero length).

Renamed *_ReadWriteAllowed() macros to *_IsReadWriteAllowed() to remain consistent with the rest of the LUFA API.

Endpoint_IsSetupReceived() macro has been renamed to Endpoint_IsSETUPReceived(), Endpoint_ClearSetupReceived() macro has been renamed to Endpoint_ClearControlSETUP(), the Pipe_IsSetupSent() macro has been renamed to Pipe_IsSETUPSent() and the Pipe_ClearSetupSent() macro is no longer applicable and should be removed - changes made to compliment the new endpoint and pipe bank management API.

Updated all demos, bootloaders and projects to use the new endpoint and pipe management APIs (thanks to Roman Thiel).

Updated library doxygen documentation, added groups, changed documentation macro functions to real functions for clarity.

Removed old endpoint and pipe aliased read/write/discard routines which did not have an explicit endian specifier for clarity.

Removed the ButtLoadTag.h header file, as no one used for its intended purpose anyway.

All comments in the library, bootloaders, demos and projects have now been spell-checked and spelling mistakes/typos corrected.

Seperated out OTG, Device and Host mode demos into seperate folders for clarity. Adjusted makefiles so that the path to the LUFA library can be set in one place.

Fixed incorrect/missing control status stage transfers on demos, bootloaders and applications (thanks to Nate Lawson).