Added missing Audio class control request definitions.

Added support for the Audio class GET STATUS request so that it is correctly ACKed when sent by the host.

Replace cast-as-char* byte access of multibyte variables with proper shifts and masks to preserve endianness across different architectures.

Replace all calls and references to _delay_ms() in the code with the architecture-agnostic Delay_MS() function.

Improve code generation for the Delay_MS() function on the AVR8 architecture when called with a constant input.

Renamed all low level Endpoint_Read_*, Endpoint_Write_* and Endpoint_Discard_* functions to use the number of bits instead of a symbolic size (Byte, Word, DWord) so that the function names are applicable and correct across all architectures.

Renamed all low level Pipe_Read_*, Pipe_Write_* and Pipe_Discard_* functions to use the number of bits instead of a symbolic size (Byte, Word, DWord) so that the function names are applicable and correct across all architectures.

Add new ARCH option to the makefiles to (eventually) specify the target device architecture. Update non-usb peripheral drivers to reflect future multiple architecture support.

Add static keyword to all project globals whose scope should be restricted to the same module as they are declared in.

Tighten up the HID class bootloader code slightly, document that it currently exceeds 2KB of bootloader space for all models other than the Series 2 USB AVRs.

Add const to all project descriptor definitions for safety.

Fixed programming errors in the AVRISP-MKII project when the programming packet is a round multiple of the endpoint bank  size under avrdude (thanks to Steffan Woltjer).

Removed SerialStream module, rolled functionality into the base USART Serial peripheral driver instead through the new Serial_CreateStream() and Serial_CreateBlockingStream() methods.

Renamed the Serial byte send/receive functions to remain consistent with the CDC driver's byte functions.

Altered the serial byte receive function to make it non-blocking.

Changed AVRISP-MKII project to use the Watchdog interrupt for command timeouts, to reduce CPU usage and free timer 0 for other uses in the future.

Altered all endpoint/pipe stream transfers so that the new BytesProcessed parameter now points to a location where the number of bytes in the transfer that have been completed can be stored (or NULL if entire transaction should be performed in one chunk).

Added new Endpoint_Null_Stream() and Pipe_Null_stream() functions.

Removed the NO_STREAM_CALLBACKS compile time option due to the new partial stream transfer feature replacing it.

Fixed errors in the incomplete Test and Measurement device demo preventing proper operation (thanks to Pavel Plotnikov).

Documentation improvements - put driver example code into its own section, fix incorrect and missing section names.

Combined page and word ISP programming mode code in the AVRISP-MKII clone project to reduce compiled size and  increase maintainability of the code.

Fixed possible programming problem in the AVRISP-MKII clone project when programming specific patterns into a target memory space that is only byte (not page) addressable.

Add DEVICE_STATE_AS_GPIOR=0 compile time option to the library projects, to reduce compiled binary size.

Fixed incorrect definition of the HID_KEYBOARD_SC_D constant in the HID class driver (thanks to Opendous Inc.).

Add extra comments to the ISPTarget.c source file in the AVRISP-MKII clone project.

Lower bulk endpoint polling rate in the descriptors to the lowest possible value to give maximum throughput.

Rename incorrectly named XPROGTarget_SendBreak() function to XPROGTarget_SendIdle(), as it is sending idle bits and not break bits.

Fixed AVRISP-MKII clone project not starting the target's program automatically after exiting TPI programming mode.

Slow AVRISP-MKII clone PDI/TPI programming speed back to 250KHz due to issues with the XPLAINBridge when PDI programming at faster rates.

Speed up XMEGANVM_WaitWhileNVMControllerBusy() by preloading the status register address into the pointer register of the target's NVM controller and then reading via a faster indirect load command.

Added new XCK_RESCUE_CLOCK_ENABLE compile time option to the AVRISP-MKII clone programmer project (thanks to Tom Light).

Fixed PDI/TPI programming speed of ~250KHz in the AVRISP-MKII Clone project, instead of the desired 500KHz.

Fixed incorrect PollingIntervalMS values in the demo/project/bootloader endpoint descriptors (thanks to MCS Electronics).

Fixed calculation of timer register reload values derived from F_CPU; must subtract one from the division result for the compare value to be correct.

Change AVRISP-MKII rescue clock speed to 4MHz to ensure that a 125KHz ISP speed works regardless of the target's fuses (i.e. DIV8 set).

Fix XPLAINBridge code broken during the changes to the Rescue Clock generation in the AVRISP-MKII clone project.

Change over all low level host mode project's descriptor comparator routines to perform the descriptor casting in a temp variable to make the code clearer and easier to modify (despite being more verbose).

Rescue clock of the AVRISP-MKII moved to the AVR's OCR1A pin, so that the clock can be generated at all times when 125KHz ISP programming mode is selected.

Changed over www.fourwalledcubicle.com links to the new www.lufa-lib.org redirect domain, including the new aliased links for LUFA-related pages such as the various download/source control mirrors and support lists.

Add descriptor class, subclass and protocol constants to the class drivers, modify all demos to use them where possible.

Move out private/internal host class driver constants to the common class driver headers, so that they can be used in the Low Level host mode demos.

Ensure all demos, projects and bootloaders use the class driver constants where possible to minimise code repetition.

Revert change to the AVRISP-MKII project for fuse byte programming via the CMDEX bit - this appears to be an error in the XMEGA manual external memory programming table.

Fixed broken FLASH/EEPROM programming in the AVRISP-MKII clone project when writing in non-paged mode and the polling byte cannot be used.

Changed default value for the reset polarity parameter in the AVRISP-MKII project so that it defaults to active low drive.

Fixed incorrect USB_DeviceState value when unconfiguring the device without an address set.

Remove dfu-programmer program switches, to ensure maximum compatibility with all dfu-programmer versions.

Added the --suppress-bootloader-mem option to the makefile dfu target, to ensure that writes to the bootloader section of the AVR's flash memory are ignored (thanks to Axel Rohde).

Fixed incorrect command name for EEPROM memory programming in the makefile dfu-ee target.

Makefile whitespace fixes.