Fixed AVRISP project not sending a full erase-and-write EEPROM command to XMEGA targets when writing to the EEPROM instead of the split write-only command (thanks to Tim Margush).

Fixed AVRISP project sending a LOAD EXTENDED ADDRESS command to 128KB AVRs after programming or reading from the last page of FLASH.

Remove incorrect check for the current device state in the Set Configuration request handler of DevChapter9, which broke Set Configuration requests to the device under most circumstances.

Move out the SPI prescaler list to a PROGMEM module-level variable in ISPTarget.c.

Fixed AVRISP-MKII clone project not correctly issuing SET EXTENDED ADDRESS commands when the extended address boundary is crossed during programming or readback (thanks to Gerard Sexton).

Fixed warnings when building the AVRISP-MKII clone project with the ENABLE_XPROG_PROTOCOL compile time option disabled.

Fixed possible device lockup when INTERRUPT_CONTROL_ENDPOINT is enabled and the control endpoint is not properly selected when the ISR completes.

The LIBUSB_FILTERDRV_COMPAT compile time option in the XPLAINBridge and AVRISP-MKII projects has been renamed LIBUSB_DRIVER_COMPAT, as it applies to all software on all platforms using the libUSB driver.

Fix Benito makefile which was accidentally changed during testing.

Fix nasty bug in USBInterrupt.c which would cause a lockup if the control endpoint was not selected at the point the USB endpoint interrupt fires when INTERRUPT_CONTROL_ENDPOINT is defined.

Add new ReportType parameter to the HID class driver device callback and host report sending routines.

Renamed internal Host mode Class driver descriptor comparator callback routines so that they all start with a uniform DCOMP_{Class Abbreviation}_ prefix.

Add svn:eol-style property to source files, so that the line endings are correctly converted to the target system's native end of line style.

Device mode class driver callbacks are now fired before the control request status stage is sent to prevent the host from timing out if another request is immediately fired and the device has a lengthy callback routine.

Inlined currently unused MIDI ProcessControlRequest routine.

Fix TeensyHID bootloader for the largest AVRs - only the ATMEGA128x needs the alternative addressing scheme.

Added new EVENT_CDC_Device_BreakSent() event and CDC_Host_SendBreak() function to the Device and Host CDC Class drivers.

Remove incorrect Abstract Call Management class specific descriptor from the CDC demos, bootloaders and projects.

Ensure that the CDC class drivers return 0 if the number of unread bytes is queried and the bank has become empty.

Make CDC class bootloader hard-reset the AVR when exited instead of a soft-reset. Reduce size of the TeensyHID bootloader slightly.

Fix the TeensyHID bootloader for the larger USB AVR devices, since Paul uses a different (undocumented) addressing scheme on these devices.

Removed software PDI/TPI emulation from the AVRISP-MKII clone project, as it was very buggy. PDI and TPI must now be implemented via seperate headers instead of the one unified ISP/TPI/PDI header.

Fixed INTERRUPT_CONTROL_ENDPOINT compile time option preventing other interrupts from occuring while the control endpoint request is being processed, causing possible lockups if a USB interrupt occurs during a transfer.

Fixed Host mode HID class driver not sending the correct report type when HID_Host_SendReportByID() was called and the HID_HOST_BOOT_PROTOCOL_ONLY compile time option is set.

Fixed Set Configuration requests not being stalled until the host has set the device's address.

Fixed possibility of internal signature retrieval being corrupted if an interrupt occurs during a signature byte read (thanks to Andrei Krainev).

Added new ENDPOINT_*_BusSuspended error code to the Endpoint function, so that the stream functions early-abort if the bus is suspended before or during a transfer.

Change AVRISP project's timeout to be interrupt based again, but make the interrupt itself interruptable and use a seperate assembly file to hand-optimize the ISR code.

Removed the cast to uint16_t on the set baud rate in the USBtoSerial project, so that the higher >1M baud rates can be selected (thanks to Steffan).

The Audio_Device_IsSampleReceived() and Audio_Device_IsReadyForNextSample() functions are now inline, to reduce overhead.

Use puts_P() and printf_P() instead of the normal variants where possible in the Host mode Class Driver demos.

Oops - relocated USBInterrupt.h header file requires adjusted include paths for the other USB driver header files.

Relocate USBInterrupt.c/.h from the HighLevel USB driver directory to the LowLevel directory as it is hardware-dependent.

USB_Init() no longer calls sei() to enable global interrupts - this must now be done in the user application once all init code has run.

Added new HCI states to properly initialize the bluetooth dongle and retrieve the local BDADDR.

Factored out Bluetooth state information into a new state structure for easy reference in the user application.

Added new StackInitialized() Bluetooth stack callback function.

Fixed HID Device Class Driver not allocating a temporary buffer when the host requests a report via the control endpoint and the user has set the PrevReportINBuffer driver configuration element to NULL (thanks to Lars Noschinski).

Clean up incomplete BluetoothHost debugging commands to use GCC extension to avoid NULL parameters when no formatting is required.

Minor documentation improvements.

Rename FunctionAttributes.h to Attributes.h, as some attributes are applicable to variables also. Add new ATTR_NOINIT attribute for global variables.

Add the beginnings of a SDP implentation to the incomplete BluetoothHost demo.

Add const attribute to the Mass Storage Host driver functions where it was applicable, but missing.

Fixed Set/Clear Feature requests directed to a non-configured endpoint not returning a stall to the host.

Make TeensyHID bootloader use an 8 byte control endpoint to match the official Teensy, just in case Paul decides to authenticate on that attribute in the future.