Clean up and speed up build tests by turning off expensive and slow size...

Clean up and speed up build tests by turning off expensive and slow size optimizations, and generation of assembly listings (*.lst) for each compiled source file.

BuildTests/BoardDriverTest/makefile

@@ -31,23 +31,23 @@ makeboardlist:
 testboards:
 	@echo "buildtest:" > BuildMakefile
 	
-	@while read line; \
-	 do \
-	   build_cfg=`grep "$$line " BoardDeviceMap.cfg | sed 's/ //g' | grep -v "#" | cut -d'=' -f2-`; \
-	   \
-	   build_board=$$line; \
-	   build_arch=`echo $$build_cfg | cut -d':' -f1`; \
-	   build_mcu=`echo $$build_cfg | cut -d':' -f2`; \
-	   \
-	   if ( test -z "$$build_cfg" ); then \
-	     echo "No matching information set for board $$build_board"; \
-	   else \
+	@while read line;                                                         \
+	 do                                                                       \
+	   build_cfg=`grep "$$line " BoardDeviceMap.cfg | grep -v "#" | cut -d'=' -f2- | sed 's/ //g'`; \
+	                                                                          \
+	   build_board=$$line;                                                    \
+	   build_arch=`echo $$build_cfg | cut -d':' -f1`;                         \
+	   build_mcu=`echo $$build_cfg | cut -d':' -f2`;                          \
+	                                                                          \
+	   if ( test -z "$$build_cfg" ); then                                     \
+	     echo "No matching information set for board $$build_board";          \
+	   else                                                                   \
 	     echo "Found board configuration for $$build_board - $$build_arch, $$build_mcu"; \
-		 \
+		                                                                      \
 		 printf "\t@echo Building dummy project for $$build_board...\n" >> BuildMakefile; \
 		 printf "\tmake -s -f makefile.%s clean\n" $$build_arch >> BuildMakefile; \
 		 printf "\tmake -s -f makefile.%s MCU=%s BOARD=%s elf\n\n" $$build_arch $$build_mcu $$build_board >> BuildMakefile; \
-	   fi; \
+	   fi;                                                                    \
 	 done < BoardList.txt
 	 
 	 $(MAKE) -f BuildMakefile buildtest

BuildTests/BoardDriverTest/makefile.avr8

@@ -149,7 +149,7 @@ ASRC =
 # Optimization level, can be [0, 1, 2, 3, s].
 #     0 = turn off optimization. s = optimize for size.
 #     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
-OPT = s
+OPT = 1
 
 
 # Debugging format.
@@ -222,7 +222,7 @@ CFLAGS += -Wstrict-prototypes
 #CFLAGS += -Wundef
 #CFLAGS += -Wunreachable-code
 #CFLAGS += -Wsign-compare
-CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
+#CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
 CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 CFLAGS += $(CSTANDARD)
 
@@ -249,7 +249,7 @@ CPPFLAGS += -Wundef
 #CPPFLAGS += -Wstrict-prototypes
 #CPPFLAGS += -Wunreachable-code
 #CPPFLAGS += -Wsign-compare
-CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
+#CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
 CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #CPPFLAGS += $(CSTANDARD)
 
@@ -263,7 +263,8 @@ CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #             files -- see avr-libc docs [FIXME: not yet described there]
 #  -listing-cont-lines: Sets the maximum number of continuation lines of hex
 #       dump that will be displayed for a given single line of source input.
-ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
+ASFLAGS = $(ADEFS)
+#ASFLAGS += -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
 
 
 #---------------- Library Options ----------------

BuildTests/BoardDriverTest/makefile.uc3

@@ -123,7 +123,7 @@ ASRC =
 # Optimization level, can be [0, 1, 2, 3, s]. 
 #     0 = turn off optimization. s = optimize for size.
 #     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
-OPT = s
+OPT = 1
 
 
 # List any extra directories to look for include files here.
@@ -185,7 +185,7 @@ CFLAGS += -fno-strict-aliasing
 CFLAGS += -Wall
 CFLAGS += -Wstrict-prototypes
 CFLAGS += -masm-addr-pseudos
-CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
+#CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
 CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 CFLAGS += $(CSTANDARD)
 
@@ -208,7 +208,7 @@ CPPFLAGS += -fno-exceptions
 CPPFLAGS += -masm-addr-pseudos
 CPPFLAGS += -Wall
 CPPFLAGS += -Wundef
-CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
+#CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
 CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #CPPFLAGS += $(CSTANDARD)
 
@@ -222,7 +222,8 @@ CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #             files -- see avr-libc docs [FIXME: not yet described there]
 #  -listing-cont-lines: Sets the maximum number of continuation lines of hex 
 #       dump that will be displayed for a given single line of source input.
-ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
+ASFLAGS = $(ADEFS)
+#ASFLAGS += -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
 
 
 #---------------- Linker Options ----------------

BuildTests/BoardDriverTest/makefile.xmega

@@ -140,7 +140,7 @@ ASRC =
 # Optimization level, can be [0, 1, 2, 3, s]. 
 #     0 = turn off optimization. s = optimize for size.
 #     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
-OPT = s
+OPT = 1
 
 
 # List any extra directories to look for include files here.
@@ -207,7 +207,7 @@ CFLAGS += -fshort-enums
 CFLAGS += -fno-strict-aliasing
 CFLAGS += -Wall
 CFLAGS += -Wstrict-prototypes
-CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
+#CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
 CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 CFLAGS += $(CSTANDARD)
 
@@ -231,7 +231,7 @@ CPPFLAGS += -fno-strict-aliasing
 CPPFLAGS += -fno-exceptions
 CPPFLAGS += -Wall
 CPPFLAGS += -Wundef
-CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
+#CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
 CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #CPPFLAGS += $(CSTANDARD)
 
@@ -245,7 +245,8 @@ CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #             files -- see avr-libc docs [FIXME: not yet described there]
 #  -listing-cont-lines: Sets the maximum number of continuation lines of hex 
 #       dump that will be displayed for a given single line of source input.
-ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
+ASFLAGS = $(ADEFS)
+#ASFLAGS += -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
 
 
 #---------------- Library Options ----------------

BuildTests/BootloaderTest/BootloaderDeviceMap.cfg

@@ -2,42 +2,42 @@
 #
 # ------------ CDC Bootloader -------------
 CDC = avr8 : at90usb1287 : NONE : 128 : 8 :
-CDC = avr8 : at90usb647 : NONE : 64 : 4 :
+CDC = avr8 : at90usb647  : NONE :  64 : 4 :
 CDC = avr8 : at90usb1286 : NONE : 128 : 8 :
-CDC = avr8 : at90usb646 : NONE : 64 : 4 :
-CDC = avr8 : atmega32u4 : NONE : 32 : 4 :
-CDC = avr8 : atmega16u4 : NONE : 16 : 4 :
-CDC = avr8 : atmega32u2 : NONE : 32 : 4 :
-CDC = avr8 : atmega16u2 : NONE : 16 : 4 :
-CDC = avr8 : atmega8u2 : NONE : 8 : 4 :
-CDC = avr8 : at90usb162 : NONE : 16 : 4 :
-CDC = avr8 : at90usb82 : NONE : 8 : 4 :
+CDC = avr8 : at90usb646  : NONE :  64 : 4 :
+CDC = avr8 : atmega32u4  : NONE :  32 : 4 :
+CDC = avr8 : atmega16u4  : NONE :  16 : 4 :
+CDC = avr8 : atmega32u2  : NONE :  32 : 4 :
+CDC = avr8 : atmega16u2  : NONE :  16 : 4 :
+CDC = avr8 : atmega8u2   : NONE :   8 : 4 :
+CDC = avr8 : at90usb162  : NONE :  16 : 4 :
+CDC = avr8 : at90usb82   : NONE :   8 : 4 :
 #
 # ------------ DFU Bootloader -------------
 DFU = avr8 : at90usb1287 : NONE : 128 : 8 :
-DFU = avr8 : at90usb647 : NONE : 64 : 4 :
+DFU = avr8 : at90usb647  : NONE :  64 : 4 :
 DFU = avr8 : at90usb1286 : NONE : 128 : 8 :
-DFU = avr8 : at90usb646 : NONE : 64 : 4 :
-DFU = avr8 : atmega32u6 : NONE : 32 : 4 :
-DFU = avr8 : atmega32u4 : NONE : 32 : 4 :
-DFU = avr8 : atmega16u4 : NONE : 16 : 4 :
-DFU = avr8 : atmega32u2 : NONE : 32 : 4 :
-DFU = avr8 : atmega16u2 : NONE : 16 : 4 :
-DFU = avr8 : atmega8u2 : NONE : 8 : 4 :
-DFU = avr8 : at90usb162 : NONE : 16 : 4 :
-DFU = avr8 : at90usb82 : NONE : 8 : 4 :
+DFU = avr8 : at90usb646  : NONE :  64 : 4 :
+DFU = avr8 : atmega32u6  : NONE :  32 : 4 :
+DFU = avr8 : atmega32u4  : NONE :  32 : 4 :
+DFU = avr8 : atmega16u4  : NONE :  16 : 4 :
+DFU = avr8 : atmega32u2  : NONE :  32 : 4 :
+DFU = avr8 : atmega16u2  : NONE :  16 : 4 :
+DFU = avr8 : atmega8u2   : NONE :   8 : 4 :
+DFU = avr8 : at90usb162  : NONE :  16 : 4 :
+DFU = avr8 : at90usb82   : NONE :   8 : 4 :
 #
 # ------------ HID Bootloader -------------
 HID = avr8 : at90usb1287 : NONE : 128 : 4 :
-HID = avr8 : at90usb647 : NONE : 64 : 4 :
+HID = avr8 : at90usb647  : NONE :  64 : 4 :
 HID = avr8 : at90usb1286 : NONE : 128 : 4 :
-HID = avr8 : at90usb646 : NONE : 64 : 4 :
-HID = avr8 : atmega32u6 : NONE : 32 : 4 :
-HID = avr8 : atmega32u4 : NONE : 32 : 4 :
-HID = avr8 : atmega16u4 : NONE : 16 : 4 :
-HID = avr8 : atmega32u2 : NONE : 32 : 2 :
-HID = avr8 : atmega16u2 : NONE : 16 : 2 :
-HID = avr8 : atmega8u2 : NONE : 8 : 2 :
-HID = avr8 : at90usb162 : NONE : 16 : 2 :
-HID = avr8 : at90usb82 : NONE : 8 : 2 :
+HID = avr8 : at90usb646  : NONE :  64 : 4 :
+HID = avr8 : atmega32u6  : NONE :  32 : 4 :
+HID = avr8 : atmega32u4  : NONE :  32 : 4 :
+HID = avr8 : atmega16u4  : NONE :  16 : 4 :
+HID = avr8 : atmega32u2  : NONE :  32 : 2 :
+HID = avr8 : atmega16u2  : NONE :  16 : 2 :
+HID = avr8 : atmega8u2   : NONE :   8 : 2 :
+HID = avr8 : at90usb162  : NONE :  16 : 2 :
+HID = avr8 : at90usb82   : NONE :   8 : 2 :
 #
\ No newline at end of file

BuildTests/BootloaderTest/makefile

@@ -27,24 +27,26 @@ end:
 testbootloaders:
 	@echo "buildtest:" > BuildMakefile
 	
-	@while read line; \
-	 do \
-	   build_cfg=`echo $$line | sed 's/ //g' | grep -v "#"`; \
-	   \
-	   if ( test -n "$$build_cfg" ); then \
+	@while read line;                                         \
+	 do                                                       \
+	   build_cfg=`echo $$line | grep -v "#" | sed 's/ //g'`;  \
+	                                                          \
+	   if ( test -n "$$build_cfg" ); then                     \
 	     build_bootloader=`echo $$build_cfg | cut -d'=' -f1`; \
-	     build_arch=`echo $$build_cfg | cut -d'=' -f2- | cut -d':' -f1`; \
-	     build_mcu=`echo $$build_cfg | cut -d'=' -f2- | cut -d':' -f2`; \
-	     build_board=`echo $$build_cfg | cut -d'=' -f2- | cut -d':' -f3`; \
-	     build_flashsize=`echo $$build_cfg | cut -d'=' -f2- | cut -d':' -f4`; \
-	     build_bootsize=`echo $$build_cfg | cut -d'=' -f2- | cut -d':' -f5`; \
-	     \
+		 build_cfg=`echo $$build_cfg | cut -d'=' -f2-`;       \
+		                                                      \
+	     build_arch=`echo $$build_cfg | cut -d':' -f1`;       \
+	     build_mcu=`echo $$build_cfg | cut -d':' -f2`;        \
+	     build_board=`echo $$build_cfg | cut -d':' -f3`;      \
+	     build_flashsize=`echo $$build_cfg | cut -d':' -f4`;  \
+	     build_bootsize=`echo $$build_cfg | cut -d':' -f5`;   \
+	                                                          \
 	     printf "Found bootloader configuration for bootloader '%s' (FLASH: %3s KB | BOOT: %3s KB | MCU: %12s / %4s)\n" $$build_bootloader $$build_flashsize $$build_bootsize $$build_mcu $$build_arch; \
-	     \
+	                                                          \
 	     printf "\t@echo Building bootloader %s - %s - FLASH: %s KB, BOOT: %s KB\n" $$build_bootloader $$build_mcu $$build_flashsize $$build_bootsize >> BuildMakefile; \
 	     printf "\tmake -s -C $(LUFA_ROOT_PATH)/Bootloaders/%s/ clean\n" $$build_bootloader >> BuildMakefile; \
 	     printf "\tmake -s -C $(LUFA_ROOT_PATH)/Bootloaders/%s/ MCU=%s BOARD=%s FLASH_SIZE_KB=%s BOOT_SECTION_SIZE_KB=%s elf\n\n" $$build_bootloader $$build_mcu $$build_board $$build_flashsize $$build_bootsize >> BuildMakefile; \
-	   fi; \
+	   fi;                                                    \
 	 done < BootloaderDeviceMap.cfg
 	 
 	 $(MAKE) -f BuildMakefile buildtest

BuildTests/ModuleTest/makefile.avr8

@@ -154,7 +154,7 @@ ASRC = Dummy.S
 # Optimization level, can be [0, 1, 2, 3, s].
 #     0 = turn off optimization. s = optimize for size.
 #     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
-OPT = s
+OPT = 1
 
 
 # Debugging format.
@@ -220,7 +220,7 @@ CFLAGS += -fpack-struct
 CFLAGS += -fshort-enums
 CFLAGS += -fno-strict-aliasing
 CFLAGS += -fno-split-wide-types
-CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
+#CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
 CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 CFLAGS += $(CSTANDARD)
 CFLAGS += -Werror
@@ -268,7 +268,7 @@ CPPFLAGS += -fshort-enums
 CPPFLAGS += -fno-exceptions
 CPPFLAGS += -Wall
 CPPFLAGS += -Wundef
-CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
+#CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
 CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 
 
@@ -281,7 +281,8 @@ CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #             files -- see avr-libc docs [FIXME: not yet described there]
 #  -listing-cont-lines: Sets the maximum number of continuation lines of hex
 #       dump that will be displayed for a given single line of source input.
-ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
+ASFLAGS = $(ADEFS)
+#ASFLAGS += -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
 
 
 #---------------- Library Options ----------------

BuildTests/ModuleTest/makefile.uc3

@@ -126,7 +126,7 @@ ASRC = Dummy.S                 \
 # Optimization level, can be [0, 1, 2, 3, s]. 
 #     0 = turn off optimization. s = optimize for size.
 #     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
-OPT = s
+OPT = 1
 
 
 # List any extra directories to look for include files here.
@@ -186,7 +186,7 @@ CFLAGS += -funsigned-bitfields
 CFLAGS += -ffunction-sections
 CFLAGS += -fno-strict-aliasing
 CFLAGS += -masm-addr-pseudos
-CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
+#CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
 CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 CFLAGS += $(CSTANDARD)
 CFLAGS += -Werror
@@ -235,7 +235,7 @@ CPPFLAGS += -fno-exceptions
 CPPFLAGS += -masm-addr-pseudos
 CPPFLAGS += -Wall
 CPPFLAGS += -Wundef
-CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
+#CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
 CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #CPPFLAGS += $(CSTANDARD)
 
@@ -249,7 +249,8 @@ CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #             files -- see avr-libc docs [FIXME: not yet described there]
 #  -listing-cont-lines: Sets the maximum number of continuation lines of hex 
 #       dump that will be displayed for a given single line of source input.
-ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst)
+ASFLAGS = $(ADEFS)
+#ASFLAGS += -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
 
 
 #---------------- Linker Options ----------------

BuildTests/ModuleTest/makefile.xmega

@@ -143,7 +143,7 @@ ASRC = Dummy.S
 # Optimization level, can be [0, 1, 2, 3, s]. 
 #     0 = turn off optimization. s = optimize for size.
 #     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
-OPT = s
+OPT = 1
 
 
 # List any extra directories to look for include files here.
@@ -209,7 +209,7 @@ CFLAGS += -fpack-struct
 CFLAGS += -fshort-enums
 CFLAGS += -fno-strict-aliasing
 CFLAGS += -fno-split-wide-types
-CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
+#CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
 CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 CFLAGS += $(CSTANDARD)
 CFLAGS += -Werror
@@ -259,7 +259,7 @@ CPPFLAGS += -fno-strict-aliasing
 CPPFLAGS += -fno-exceptions
 CPPFLAGS += -Wall
 CPPFLAGS += -Wundef
-CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
+#CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
 CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #CPPFLAGS += $(CSTANDARD)
 
@@ -273,7 +273,8 @@ CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #             files -- see avr-libc docs [FIXME: not yet described there]
 #  -listing-cont-lines: Sets the maximum number of continuation lines of hex 
 #       dump that will be displayed for a given single line of source input.
-ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
+ASFLAGS = $(ADEFS)
+#ASFLAGS += -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
 
 
 #---------------- Library Options ----------------

BuildTests/SingleUSBModeTest/makefile.avr8

@@ -150,7 +150,7 @@ ASRC = Dummy.S
 # Optimization level, can be [0, 1, 2, 3, s].
 #     0 = turn off optimization. s = optimize for size.
 #     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
-OPT = s
+OPT = 1
 
 
 # Debugging format.
@@ -223,7 +223,7 @@ CFLAGS += -Wstrict-prototypes
 #CFLAGS += -Wundef
 #CFLAGS += -Wunreachable-code
 #CFLAGS += -Wsign-compare
-CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
+#CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
 CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 CFLAGS += $(CSTANDARD)
 
@@ -250,7 +250,7 @@ CPPFLAGS += -Wundef
 #CPPFLAGS += -Wstrict-prototypes
 #CPPFLAGS += -Wunreachable-code
 #CPPFLAGS += -Wsign-compare
-CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
+#CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
 CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #CPPFLAGS += $(CSTANDARD)
 
@@ -264,7 +264,8 @@ CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #             files -- see avr-libc docs [FIXME: not yet described there]
 #  -listing-cont-lines: Sets the maximum number of continuation lines of hex
 #       dump that will be displayed for a given single line of source input.
-ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
+ASFLAGS = $(ADEFS)
+#ASFLAGS += -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
 
 
 #---------------- Library Options ----------------

BuildTests/SingleUSBModeTest/makefile.uc3

@@ -124,7 +124,7 @@ ASRC = Dummy.S
 # Optimization level, can be [0, 1, 2, 3, s]. 
 #     0 = turn off optimization. s = optimize for size.
 #     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
-OPT = s
+OPT = 1
 
 
 # List any extra directories to look for include files here.
@@ -186,7 +186,7 @@ CFLAGS += -fno-strict-aliasing
 CFLAGS += -Wall
 CFLAGS += -Wstrict-prototypes
 CFLAGS += -masm-addr-pseudos
-CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
+#CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
 CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 CFLAGS += $(CSTANDARD)
 
@@ -209,7 +209,7 @@ CPPFLAGS += -fno-exceptions
 CPPFLAGS += -masm-addr-pseudos
 CPPFLAGS += -Wall
 CPPFLAGS += -Wundef
-CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
+#CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
 CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #CPPFLAGS += $(CSTANDARD)
 
@@ -223,7 +223,8 @@ CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #             files -- see avr-libc docs [FIXME: not yet described there]
 #  -listing-cont-lines: Sets the maximum number of continuation lines of hex 
 #       dump that will be displayed for a given single line of source input.
-ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
+ASFLAGS = $(ADEFS)
+#ASFLAGS += -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
 
 
 #---------------- Linker Options ----------------

BuildTests/SingleUSBModeTest/makefile.xmega

@@ -141,7 +141,7 @@ ASRC = Dummy.S
 # Optimization level, can be [0, 1, 2, 3, s]. 
 #     0 = turn off optimization. s = optimize for size.
 #     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
-OPT = s
+OPT = 1
 
 
 # List any extra directories to look for include files here.
@@ -208,7 +208,7 @@ CFLAGS += -fshort-enums
 CFLAGS += -fno-strict-aliasing
 CFLAGS += -Wall
 CFLAGS += -Wstrict-prototypes
-CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
+#CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
 CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 CFLAGS += $(CSTANDARD)
 
@@ -232,7 +232,7 @@ CPPFLAGS += -fno-strict-aliasing
 CPPFLAGS += -fno-exceptions
 CPPFLAGS += -Wall
 CPPFLAGS += -Wundef
-CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
+#CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
 CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #CPPFLAGS += $(CSTANDARD)
 
@@ -246,7 +246,8 @@ CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #             files -- see avr-libc docs [FIXME: not yet described there]
 #  -listing-cont-lines: Sets the maximum number of continuation lines of hex 
 #       dump that will be displayed for a given single line of source input.
-ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
+ASFLAGS = $(ADEFS)
+#ASFLAGS += -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
 
 
 #---------------- Library Options ----------------

LUFA/CodeTemplates/makefile_template.uc3

@@ -188,7 +188,7 @@ CFLAGS += -fno-strict-aliasing
 CFLAGS += -Wall
 CFLAGS += -Wstrict-prototypes
 CFLAGS += -masm-addr-pseudos
-CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
+#CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
 CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 CFLAGS += $(CSTANDARD)
 
@@ -211,7 +211,7 @@ CPPFLAGS += -fno-exceptions
 CPPFLAGS += -masm-addr-pseudos
 CPPFLAGS += -Wall
 CPPFLAGS += -Wundef
-CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
+#CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
 CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #CPPFLAGS += $(CSTANDARD)
 
@@ -225,7 +225,8 @@ CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 #             files -- see avr-libc docs [FIXME: not yet described there]
 #  -listing-cont-lines: Sets the maximum number of continuation lines of hex 
 #       dump that will be displayed for a given single line of source input.
-ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
+ASFLAGS = $(ADEFS)
+#ASFLAGS += -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
 
 
 #---------------- Linker Options ----------------