Remove the timeout period extension code from the AVRISP project, as no single command should ever exceed the maximum timeout period. Extend timeout period to 1 second per command, so that an accidental timeout will never occur.

Spell check code and manual pages. Remove custom Doxygen CSS stylesheet, as the new 1.7 Doxygen's default stylesheet is much better.

Fixed AVRISP project not sending a full erase-and-write EEPROM command to XMEGA targets when writing to the EEPROM instead of the split write-only command (thanks to Tim Margush).

Add svn:eol-style property to source files, so that the line endings are correctly converted to the target system's native end of line style.

Add user callback function to the Bluetooth host demo to filter out connections from remote devices. Add in ability to reject connections based on their bluetooth device address.

Clean up RelayBoard project code.

Make AVRISP project clear the XMEGA target's reset register twice; this does not appear to take affect properly the first time under some circumstances.

Added WIN_LIBUSB_COMPAT compile time option to the AVRISP programmer project to make the code compatible with Windows builds of avrdude at the expense of AVRStudio compatibility.

Fixed PDI programming mode in the AVRISP programmer project not exiting programming mode correctly (clear target Reset key twice, set /RESET pin to pullup).

Add newlines to the MIDI event printf() statements in the MIDI host demos.

Fixed lack of SECTION ERASE command in TPI programming mode of the AVRISP project preventing fuses from being cleared.

Fix AVRISP-MKII clone project's TPI Chip Erase command processing - ensure erase location is the high byte in the given address space, check NVMBUSY for completion rather than the NVM Bus Enable bit.

Change If-Else chains over to switch statements in XPROGProtocol.c for clarity.

Ensure TPI enable timing requirements are met in AVRISP-MKII programmer. Remove invalid code in the TPI read/write functions.

Minor code cleanups, remove TemperatureDataLogger host application's Visual Studio Solution files, add LibHIDNet license files.

Changed XPLAINBridge project to be both a USB to USART bridge and a PDI programmer, based on the state of a mode select pin.

Clean up and add more comments to the AVRISP-MKII project. Make sure the SPI_MULTI command handler supports multiple packet responses. Use slightly smaller/faster repeated indirect-load commands when retrieving the PDI target's memory CRCs.

Reduced guard bit time in the AVRISP project PDI/TPI protocols to reduce the time needed to reverse the data communication direction.

Fix TPI NVM Write handler -- AVRStudio sends out writes in page sized chunks, not byte sized chunks.

Add first draft of the TPI NVM commands for reading, writing and erasing a target. Needs testing when physical access to a part is available.

Add dummy undocumented TPI XPROG parameters to the AVRISP project so that TPI programming mode can be entered.

Added command timeout to the AVRISP project so that incorrectly connected targets no longer freeze the device.

Removed string descriptors from the TeensyHID bootloader to reduce its size.

Complete combining of PDI and TPI target communication code files, stub out TINY NVM controller functions.

Combine AVRISP project TPI and PDI lib directories - these protocols use the same underlying XPROG wrapper for the host-to-programmer command wrapping.

Make seperate ISP, PDI and TPI folders in the AVRISP project Lib subdirectory to hold each protocol's files.

Use default NVM base address in the AVRISP programmer project in case the host programmer software doesn't set it correctly.

Complete initial working revision of PDI programming in the AVRISP project (XMEGAs can now be programmed by the firmware).

Fix a bug in the Still Image Host Class driver where the returned block status code was being truncated.

Add programming support to the AVRISP project's PDI programming mode; paged memory writes are not currently functional.

Fix error in AVRISP programmer when repeatedly using PDI mode via the hardware USART due to the SendByte routine not clearing the Transmit Complete USART flag.

Add Doxygen documentation to the completed portions of the PDI programming protocol in the AVRISP project.

Use the PDI REPEAT instruction in the PDI programmer code to reduce protocol overhead and greatly improve transfer throughput. Switch bit-bang USART in the AVRISP project to Timer 1, so that Timer 0 can be used for hardware timeouts while waiting for the NVM bus or controller to become ready.