Fix Mass Storage Host Class driver GetMaxLUN command - incorrect function return codes used in comparison to check for success.

Add HID Host Class driver functions to set the report protocol, add more class driver documentation.

Remove USE_NONSTANDARD_DESCRIPTOR_NAMES compile time token, split out standard descriptors into seperate USB_Descriptor_* and USB_StdDescriptor_* structures so that both can be used within the one project.

Add guard to the HID Host Class driver SetProtocol command, to ensure that the device supports boot protocol mode before issuing the request.

Corrected incorrect signature bytes for the AT90USB82 and added support for the ATMEGAXX2 variant AVRs to the DFU bootloader.

Added warning to the EVENT_USB_Device_Connect() and EVENT_USB_Device_Disconnect() events that they may be fired multiple times during device enumeration on the series 2 AVRs.

Changed the parameters and behaviour of the USB_GetDeviceConfigDescriptor() function so that it now performs size checks and data validations internally, to simplify user code.

Fix up references to functions in the Endpoint/Pipe documentation.

Added new Endpoint_SetEndpointDirection() macro to set the current endpoint direction for bidirectional endpoints.

Renamed internal USB_INT_ENDPOINT_SETUP macro to USB_INT_RXSTPI to fit in with the rest of the interrupt vector macros.

Added new EVENT_USB_Device_StartOfFrame() event, controlled by the new USB_Device_EnableSOFEvents() and USB_Device_DisableSOFEvents() macros to give bus-synchronised millisecond interrupts when in USB device mode.

Make Benito ping-pong LED code more explicit, using masks of the TX and RX LED masks for ping-pong toggle rather than the ambiguous LED "Busy" mask.

Fix incorrect event name in MassStorageHost.c.

Changed over manual loops waiting for endpoints to be ready to use the library Endpoint_WaitUntilReady() function for robustness. Fixes issues with terminated transfers on the host locking up USB devices.

Renamed all library events to properly seperate out Device and Host mode events. Changed the firing conditions for some events to ensure that events are fired by their own USB mode only.

Remove VBUS events - not needed as the library takes care of VBUS detection and feedback on supported AVRs via the USB_Device_Connected and USB_Device_Disconnected events.

Fixed incorrect Host state assignment in the incomplete BluetoothHost demo.

Removed interrupt disable/enable from the Device mode control request processing routines, as they can cause problems with user code and can cause infinite spinlocks under some circumstances.

Added new LUFA logo from EDIGMA.COM.

Renamed USB_Device_SetHighSpeed() to USB_Device_SetFullSpeed() so that the correct terminology is used (thanks to Brian Dickman).

Fix USB_PLL_Off() call in the series 4, 6 and 7 microcontroller disconnect interrupt handler code, which wasn't guarded by a test of USB_Options to check if the user has specified manual PLL control (thanks to Brian Dickman).

Fix redefinition warning when USB_DEVICE_ONLY is set on an AVR which does not support USB host mode.

Better solution - change compile time token names to DEVICE_STATE_AS_GPIOR and HOST_STATE_AS_GPIOR and allow the user to set them to the index of the GPIOR register within the device to use.

Added HOST_STATE_AS_GPIOR1 and DEVICE_STATE_AS_GPIOR0 compile time options, the latter of which is used in the bootloaders, to reduce code size.

Ensure that the USB_DeviceState variable is properly set upon wakeup events, to the Addressed or Configured state as needed.

Add explicit support for the AT90USB646 to the Teensy bootloader now that PJRC have released the Teensy++ board.

Ensure unfinished SideShow demo uses an unallocated PID value within the LUFA range.

Added new Endpoint_ClearStatusStage() convenience function to assist with the status stages of control transfers.

Removed vague USB_IsConnected global - test USB_DeviceState or USB_HostState explicitly to gain previous functionality.

Removed USB_IsSuspended global - test USB_DeviceState against DEVICE_STATE_Suspended instead.

Fixed possible enumeration errors from spinloops which may fail to exit if the USB connection is severed before the exit condition becomes true.

Fixed Host mode to Device mode UID change not causing a USB Disconnect event when a device was connected.

Added parameter directions to function parameter documentation.

Added new experimental FAST_STREAM_FUNCTIONS compile time option to speed up stream transfers at the expense of a higher FLASH consumption (needs testing to verify improved throughput).

Added new USE_INTERNAL_SERIAL define for using the unique serial numbers in some AVR models as the USB device's serial number, added NO_INTERNAL_SERIAL compile time option to turn off new serial number reading code. Updated Mass Storage and CDC based demos to use the new device serial number if the device it is compiled for supports it.

Added USE_INTERNAL_SERIAL compile time option to automatically read out the internal unique serial number as the device's serial number descriptor on supported AVR models.

Extend USB_GetDeviceConfigDescriptor() routine to require the configuration number within the device to fetch, to add support for multi-configuration devices.

Added new USB_Host_ClearPipeStall() convenience function to clear a stall condition on an attached device's endpoint.

Added new USB_Host_GetDeviceDescriptor() convenience function to retrieve the attached device's Device descriptor.

Make Pipe_ConfigurePipe() mask the given endpoint number against PIPE_EPNUM_MASK to ensure the endpoint IN direction bit is cleared to prevent endpoint type corruption.

Fix documentation mentioning Pipe_GetCurrentToken() function when real name is Pipe_GetPipeToken().

Changed per-device controller preprocessor checks over to per-device series for better device control.

Fixed error in Endpoint.c using HSOFI rather than SOFI for counting elapsed milliseconds.

Redocumented all device demos, now that they have changed over to the new USB class drivers.

Added C linkage to class drivers for C++ support.

Added prefixes to most of the class driver constants to prevent name clashes.

Removed new Start of Frame event from the library; performance suffered far too much and it was only useful in one of the standard classes (HID). Altered HID demos to use the previous method of tracking millisecond periods via a hardware timer rather than the SOF events.

Fixed MIDI class driver blocking on unread events to the host.

Commit of new class abstraction APIs for all device demos other than the MIDI demo - not documented yet.

Removed scheduler and memory allocation libraries.

Added new EVENT_USB_StartOfFrame event in the library to indicate the start of each USB frame (when generated).

Removed Tx interrupt from the USBtoSerial demo; now sends characters via polling to ensure more time for the Rx interrupt.

Deleted StdDescriptors.c, renamed USB_GetDescriptor() to CALLBACK_USB_GetDescriptor, moved ConfigDescriptor.c/.h from the LUFA/Drivers/USB/Class/ directory to LUFA/Drivers/USB/HighLevel/ in preperation for the new USB class APIs.

USB_IsConnected is now cleared before the USB_Disconnect() event is fired in response to VBUS being removed.

Minor documentation improvements.

Fixed incorrect ENDPOINT_EPNUM_MASK mask preventing endpoints above EP3 from being selected (thanks to Jonathan Oakley).

Removed STREAM_CALLBACK() macro - callbacks now use regular function definitions to clarify user code.

Removed DESCRIPTOR_COMPARATOR() macro - comparators should now use regular function definitions to clarify user code.

Create a new function pointer type in StreamCallbacks.h for endpoint/pipe stream callbacks, to make stream function prototypes clearer.

Removed all user pipe/endpoint interrupt APIs, added internal library support for interrupt driven control endpoints when in device mode by defining INTERRUPT_CONTROL_ENDPOINT token and passing it to the compiler via the -D switch.

Moved USB Host state machine code out from USBTask.c and into Host.c, where it more properly belongs.