Rename incorrectly named XPROGTarget_SendBreak() function to XPROGTarget_SendIdle(), as it is sending idle bits and not break bits.

Fixed AVRISP-MKII clone project not starting the target's program automatically after exiting TPI programming mode.

Slow AVRISP-MKII clone PDI/TPI programming speed back to 250KHz due to issues with the XPLAINBridge when PDI programming at faster rates.

Speed up XMEGANVM_WaitWhileNVMControllerBusy() by preloading the status register address into the pointer register of the target's NVM controller and then reading via a faster indirect load command.

Added new XCK_RESCUE_CLOCK_ENABLE compile time option to the AVRISP-MKII clone programmer project (thanks to Tom Light).

Fixed PDI/TPI programming speed of ~250KHz in the AVRISP-MKII Clone project, instead of the desired 500KHz.

Fixed calculation of timer register reload values derived from F_CPU; must subtract one from the division result for the compare value to be correct.

Change AVRISP-MKII rescue clock speed to 4MHz to ensure that a 125KHz ISP speed works regardless of the target's fuses (i.e. DIV8 set).

Fix XPLAINBridge code broken during the changes to the Rescue Clock generation in the AVRISP-MKII clone project.

Change over all low level host mode project's descriptor comparator routines to perform the descriptor casting in a temp variable to make the code clearer and easier to modify (despite being more verbose).

Rescue clock of the AVRISP-MKII moved to the AVR's OCR1A pin, so that the clock can be generated at all times when 125KHz ISP programming mode is selected.

Changed over www.fourwalledcubicle.com links to the new www.lufa-lib.org redirect domain, including the new aliased links for LUFA-related pages such as the various download/source control mirrors and support lists.

Revert change to the AVRISP-MKII project for fuse byte programming via the CMDEX bit - this appears to be an error in the XMEGA manual external memory programming table.

Fixed broken FLASH/EEPROM programming in the AVRISP-MKII clone project when writing in non-paged mode and the polling byte cannot be used.

Changed default value for the reset polarity parameter in the AVRISP-MKII project so that it defaults to active low drive.

Fixed incorrect USB_DeviceState value when unconfiguring the device without an address set.

Fix incorrect ADC driver documentation for the parameters of ADC_Init(), fix incorrect call to ADC_Init() in the TemperatureDatalogger project.

Added compile time error to the AVRISP-MKII project when built for the U4 chips, as the default VTARGET detection ADC channel does not exist on these chips (thanks to Marco).

More spell checking of all source files -- correct missed errors, switch to EN-GB spelling dictionary.

Remove obsolete macros and preprocessor checks from the AVRISP-MKII project's V2Protocol command handler header file.

Added support to the AVRISP-MKII project for ISP speeds slower than 125KHz via a new software SPI driver.

Added new SPI_ORDER_* data order masks to the SPI peripheral driver.

Future proof the XPROG protocol of the AVRISP-MKII project, so that non PDI and TPI requests return failure.

Update all demos, projects and bootloaders to indent all function parameters, one per line, for better readability.

Add missing const qualifiers to the demos.

Change AVRISP-MKII and XPLAINBridge descriptors to indicate that the device is bus-powered only. Add compile time options to reduce the compiled size of the firmware.

Remove the timeout period extension code from the AVRISP project, as no single command should ever exceed the maximum timeout period. Extend timeout period to 1 second per command, so that an accidental timeout will never occur.

Make loops in AVRISP-MKII Clone project's XPROG protocol infinite rather than looping on the timeout value, as this is already checked inside the loop anyway.

Spell check code and manual pages. Remove custom Doxygen CSS stylesheet, as the new 1.7 Doxygen's default stylesheet is much better.

Added new VTARGET_REF_VOLTS and VTARGET_SCALE_FACTOR compile time defines to the AVRISP-MKII programmer project to set the VTARGET reference voltage and scale factor.

Fixed XPLAINBridge project not correctly reading the XMEGA's supply voltage when reporting back to the host.

The EEPROM stream read/write functions now use eeprom_update_byte() instead of eeprom_write_byte(), so that only changed bytes are written to EEPROM to preserve its lifespan.

Changed over the AVRISP-MKII and TemperatureDataLogger projects to use eeprom_update_byte() when writing non-volatile parameters to EEPROM to preserve its lifespan.

Fixed AVRISP project not sending a full erase-and-write EEPROM command to XMEGA targets when writing to the EEPROM instead of the split write-only command (thanks to Tim Margush).

Fixed AVRISP project sending a LOAD EXTENDED ADDRESS command to 128KB AVRs after programming or reading from the last page of FLASH.

Remove incorrect check for the current device state in the Set Configuration request handler of DevChapter9, which broke Set Configuration requests to the device under most circumstances.

Move out the SPI prescaler list to a PROGMEM module-level variable in ISPTarget.c.

Fixed AVRISP-MKII clone project not correctly issuing SET EXTENDED ADDRESS commands when the extended address boundary is crossed during programming or readback (thanks to Gerard Sexton).

Fixed warnings when building the AVRISP-MKII clone project with the ENABLE_XPROG_PROTOCOL compile time option disabled.

Add svn:eol-style property to source files, so that the line endings are correctly converted to the target system's native end of line style.

Removed software PDI/TPI emulation from the AVRISP-MKII clone project, as it was very buggy. PDI and TPI must now be implemented via seperate headers instead of the one unified ISP/TPI/PDI header.