Fixed AVRISP programmer demo -- can now connect to a target and read/write Sig/Lock/Fuse/OSCCAL bytes successfully.

Changed SPI_Init() to allow for the clock polarity and data sample modes to be set.

Changed Dataflash_Init() to no longer call SPI_Init() automatically.

Added V2Protocol handlers to the AVRISP project to enter/exit programming mode, and read/write fuses, lockbits, OSCCAL and Signature bytes.

Added ShutDown functions for all hardware peripheral drivers, so that peripherals can be turned off after use.

Fix up references to functions in the Endpoint/Pipe documentation.

Change spinloop in the AVRISP project Unknown V2 Protocol Command handler to use Endpoint_WaitUntilReady() instead to prevent infinite loops.

Moved out the handling of V2 Protocol parameters to a seperate set of files. Added parameter privellages, so that an error can be returned to the host when trying to perform a get/set value action on a parameter without the correct privellages.

Added documentation of the makefile CDEFS values to the MagStripe project.

Fixed invalid data being returned when a GetStatus request is issued in Device mode with an unhandled data recipient.

Fix up Programmers Notepad Project file to show new Projects directory layout. Remove now moved AVRISP project from the Projects directory makefile.

Move AVRISP Programmer project to a new Unfinished subdirectory of Project while it is under development.

Enhancements to the AVRISP Programmer project to attempt to get AVRStudio to communicate with the device.

Added new Endpoint_SetEndpointDirection() macro to set the current endpoint direction for bidirectional endpoints.

Renamed internal USB_INT_ENDPOINT_SETUP macro to USB_INT_RXSTPI to fit in with the rest of the interrupt vector macros.

Added new EVENT_USB_Device_StartOfFrame() event, controlled by the new USB_Device_EnableSOFEvents() and USB_Device_DisableSOFEvents() macros to give bus-synchronised millisecond interrupts when in USB device mode.

Adjust endpoint polling intervals for HID demos, to make them compliant with the 10ms minimum polling period for Low Speed devices.

Make Benito ping-pong LED code more explicit, using masks of the TX and RX LED masks for ping-pong toggle rather than the ambiguous LED "Busy" mask.

Fix incorrect event name in MassStorageHost.c.

Fixed issue in USBtoSerial demos where the USART Rx line was not having its pullup enabled at startup, leading to noise being received from the Rx pin when left floating.

Removed unused relative Common.h header include from the DriverStubs board stub drivers.

Fixed Benito programmer, use the correct LED functions where needed to ensure correct status display at all times.

Renamed all library events to properly seperate out Device and Host mode events. Changed the firing conditions for some events to ensure that events are fired by their own USB mode only.

Remove VBUS events - not needed as the library takes care of VBUS detection and feedback on supported AVRs via the USB_Device_Connected and USB_Device_Disconnected events.

Fixed incorrect Host state assignment in the incomplete BluetoothHost demo.

Rename TOTAL_NUM_CONFIGURATIONS to FIXED_NUM_CONFIGURATIONS, to match the existing FIXED_CONTROL_ENDPOINT_SIZE compile time option. Add FIXED_NUM_CONFIGURATIONS to the descriptors of each project using the option.

Fix demos based on the device mode HID class driver, as well as the driver itself. Changed HID device class driver to require the user to give a buffer and size to hold the previously generated report, for comparison purposes, and altered the prototype of the CALLBACK_HID_Device_CreateHIDReport() function so that reports can be sent to the host even if there are no apparent changes (useful for relative movements in mice, etc.).

Add new HID_Device_MillisecondElapsed() function to the HID device Class driver, to move the burden of managing the Idle period of each instance to the library and not the user application.

Fix to HID device mode Class driver, so that new reports are compared against the old, and updated reports made within the idle period are sent immediately to the host.

Extend the automatic serial number descriptor code to read out and send all 10 bytes (20 characters) of the internal serial number on supported AVRs, rather than just the first 6 bytes (12 characters).

Change project makefiles so that the current target settings and not just the board selection is printed during the build process.

Fix warning in AudioOutput demos when AUDIO_OUT_STEREO output mode is selected.

Changed AudioOutput demos to explicitly use timer 3 - the smaller USB AVRs where timer 1 was needed instead did not have the endpoint size neccesary for good audio throughput anyway.

Fix Benito documentation indicating erronously that the project used the HID USB class instead of the CDC class.

State information for class drivers is now zeroed out during enumeration (both in device and host mode) to ensure sane values after each enumeration. User code should no longer explicitly set state information as this is no longer preserved.

Ensure new Benito Programmer project matches Don's established LED behaviour - flash LED while generating target /RESET pulse, ping-pong LEDs during enumeration.

Added new Benito project, a simple modified USB-to-Serial bridge for the programming of AVRs using the official Arduino bootloader.

Added new Endpoint_ClearStatusStage() convenience function to assist with the status stages of control transfers.

Removed vague USB_IsConnected global - test USB_DeviceState or USB_HostState explicitly to gain previous functionality.

Removed USB_IsSuspended global - test USB_DeviceState against DEVICE_STATE_Suspended instead.

Fixed possible enumeration errors from spinloops which may fail to exit if the USB connection is severed before the exit condition becomes true.

Change Doxygen configuration files to not produce 4096 directories for the documentation files -- the LUFA components do not generate enough documentation files to justify the large performance hit of creating so many directories.

Fix missing Doxygen documentation in the Class Driver Mass Storage Device demo.

Magstripe Project: Ensure that empty tracks still print out a newline seperator so that the host always knows what track data is being sent.

Updates to PrinterHost demo to include some PCL test data plus fixes to the GetDeviceID routine.

Fixed error in GenericHID descriptors preventing it from passing the USB-IF HID tests (thanks to Søren Greiner).

Added new TOTAL_NUM_CONFIGURATIONS option, removed USE_SINGLE_DEVICE_CONFIGURATION compile time option (but silently convert it to USE_SINGLE_DEVICE_CONFIGURATION internally for compatibility).

Added new USE_FLASH_DESCRIPTORS compile time option. By default, descriptors can now lie in mixed memory spaces (specified by a new parameter to the CALLBACK_USB_GetDescriptor() function) unless one of the USE_*_DESCRIPTORS compile time option is specified.

Documented FAST_STREAM_TRANSFERS compile time option.

Reduced the TCP window size for the RNDIS demos (Class and LowLevel) to make them compatible with the AT90USB64x.

Added new HOST_STATE_WaitForDeviceRemoval host state machine state for non-blocking disabling of device communications until the device has been removed (for use when an error occurs or communications with the device have completed). Changed over all host mode demos to use the new state.

Added verbose documentation for each of the USB Host state machine states.