Combined page and word ISP programming mode code in the AVRISP-MKII clone project to reduce compiled size and  increase maintainability of the code.

Fixed possible programming problem in the AVRISP-MKII clone project when programming specific patterns into a target memory space that is only byte (not page) addressable.

Add DEVICE_STATE_AS_GPIOR=0 compile time option to the library projects, to reduce compiled binary size.

Fixed incorrect definition of the HID_KEYBOARD_SC_D constant in the HID class driver (thanks to Opendous Inc.).

Add extra comments to the ISPTarget.c source file in the AVRISP-MKII clone project.

Lower bulk endpoint polling rate in the descriptors to the lowest possible value to give maximum throughput.

Rename incorrectly named XPROGTarget_SendBreak() function to XPROGTarget_SendIdle(), as it is sending idle bits and not break bits.

Fixed AVRISP-MKII clone project not starting the target's program automatically after exiting TPI programming mode.

Slow AVRISP-MKII clone PDI/TPI programming speed back to 250KHz due to issues with the XPLAINBridge when PDI programming at faster rates.

Speed up XMEGANVM_WaitWhileNVMControllerBusy() by preloading the status register address into the pointer register of the target's NVM controller and then reading via a faster indirect load command.

Added new XCK_RESCUE_CLOCK_ENABLE compile time option to the AVRISP-MKII clone programmer project (thanks to Tom Light).

Fixed PDI/TPI programming speed of ~250KHz in the AVRISP-MKII Clone project, instead of the desired 500KHz.

Fixed incorrect PollingIntervalMS values in the demo/project/bootloader endpoint descriptors (thanks to MCS Electronics).

Fixed calculation of timer register reload values derived from F_CPU; must subtract one from the division result for the compare value to be correct.

Change AVRISP-MKII rescue clock speed to 4MHz to ensure that a 125KHz ISP speed works regardless of the target's fuses (i.e. DIV8 set).

Fix XPLAINBridge code broken during the changes to the Rescue Clock generation in the AVRISP-MKII clone project.

Change over all low level host mode project's descriptor comparator routines to perform the descriptor casting in a temp variable to make the code clearer and easier to modify (despite being more verbose).

Rescue clock of the AVRISP-MKII moved to the AVR's OCR1A pin, so that the clock can be generated at all times when 125KHz ISP programming mode is selected.

Changed over www.fourwalledcubicle.com links to the new www.lufa-lib.org redirect domain, including the new aliased links for LUFA-related pages such as the various download/source control mirrors and support lists.

Add descriptor class, subclass and protocol constants to the class drivers, modify all demos to use them where possible.

Move out private/internal host class driver constants to the common class driver headers, so that they can be used in the Low Level host mode demos.

Ensure all demos, projects and bootloaders use the class driver constants where possible to minimise code repetition.

Revert change to the AVRISP-MKII project for fuse byte programming via the CMDEX bit - this appears to be an error in the XMEGA manual external memory programming table.

Fixed broken FLASH/EEPROM programming in the AVRISP-MKII clone project when writing in non-paged mode and the polling byte cannot be used.

Changed default value for the reset polarity parameter in the AVRISP-MKII project so that it defaults to active low drive.

Fixed incorrect USB_DeviceState value when unconfiguring the device without an address set.

Remove dfu-programmer program switches, to ensure maximum compatibility with all dfu-programmer versions.

Added the --suppress-bootloader-mem option to the makefile dfu target, to ensure that writes to the bootloader section of the AVR's flash memory are ignored (thanks to Axel Rohde).

Fixed incorrect command name for EEPROM memory programming in the makefile dfu-ee target.

Makefile whitespace fixes.

Make project makefiles correctly clean intermeditary build files from assembly and C++ sources (thanks to Daniel Czigany).

Clarify in the project documentation files what the each of the different USB AVR device "series" comprises of.

Fix incorrect ADC driver documentation for the parameters of ADC_Init(), fix incorrect call to ADC_Init() in the TemperatureDatalogger project.

Changed the signature of the CALLBACK_USB_GetDescriptor() callback function so that the descriptor pointer is const, to remove the need for extra casting inside the callback (thanks to Jonathan Kollasch).

Added compile time error to the AVRISP-MKII project when built for the U4 chips, as the default VTARGET detection ADC channel does not exist on these chips (thanks to Marco).

Removed complicated logic for the Endpoint_ConfigureEndpoint() function to use inlined or function called versions depending of if the given bank size is a compile time constant, as the compiler does a better job of optimizing with basic code.

Changed over all device demos to use a clearer algorithm for the configuring of the application's endpoints.

Fix invocations of avr-size in all makefiles broken on unpatched *nix systems, due to the recent update to the latest WinAVR makefile template.

Invert the logic for the VBUS power light in the AVRISP-MKII project for the USBTINY-MKII board target.

More spell checking of all source files -- correct missed errors, switch to EN-GB spelling dictionary.

Add special support to the AVRISP-MKII for the new model USBTINY-MKII's additional LED to indicate target power source.

Add support to the USBTINY-MKII's additional LED in the board's LED driver header.

Changed LED indicator masks for the AVRISP-MKII project, so that there are defined roles for each LED.

Remove obsolete macros and preprocessor checks from the AVRISP-MKII project's V2Protocol command handler header file.

Added support to the AVRISP-MKII project for ISP speeds slower than 125KHz via a new software SPI driver.

Added new SPI_ORDER_* data order masks to the SPI peripheral driver.