Split out NVM access code in the AVRISP project into a seperate NVMTarget.c source file and header. Make NVM register accesses use the NVM base address as set by the host, rather than using the fixed value from the XMEGA datasheet.

The AVRISP project can now enter PDI mode under both bit-bang and hardware USART connection modes, tested against the XPLAIN board hardware. Still need to complete higher level NVM access code so that the device's memories can be read and written.

Fix PDI code - must send NVM enable key least significant byte first, need to make sure Tx and Rx is switched correctly including disabling the output on the Tx line when receiving.

Fix AVRISP PDI protocol - make sure inverted masks have the appropriate parenthesis around them, make sure the BREAK command for the hardware USART has 12 clock cycles exactly. Poll NVM Enable bit in the target's STATUS PDI register with a timeout, as it is not set immediately.

Change over AVRISP project to have both hardware USART and software USART modes for the PDI protocol, when enabled. Fix up PDI initialisation routines.

Fix inverted bit-banged USART logic in the AVRISP project for PDI programming. Add a delay to the clock toggling in the AVRISP project to ensure that the programming speed does not exceed 10MHz under any conditions to satisfy the limits in the datasheet for all target voltages. Fix incorrect pin being used as the DATA in in PDI programming mode.

Document the PDI programming routines implemented so far in the AVRISP project. Add ability to selectively disable ISP programming support in addition to the existing ability to disable PDI programming support.

Started implementing the low level PDI protocol in the AVRISP project, for XMEGA device programming.

Factor out all the ISP related code into a seperate ISPProtocol set of files in the AVRISP Clone programmer project, to clearly seperate out the programming protocols when PDI programming is implemented.

Remove USE_NONSTANDARD_DESCRIPTOR_NAMES compile time token, split out standard descriptors into seperate USB_Descriptor_* and USB_StdDescriptor_* structures so that both can be used within the one project.

Add guard to the HID Host Class driver SetProtocol command, to ensure that the device supports boot protocol mode before issuing the request.

Add in new invalid event hook check targets to project makefiles to produce compilation errors when invalid event names are used in a project.

Re-add in flip, flip-ee, dfu and dfu-ee targets to project makefiles (thanks to Opendous Inc.)

Fix allowable F_CPU values comment in project makefiles.

Make AVRISP project build again - fix incorrect preprocessor directive in V2Protocol.c, fix makefile LUFA_PATH.

Fix to V2 Protocol for Fuse/Sig/Lock byte read -- off by one error on the array when writing back the response from the device.

FLASH/EEPROM reading and writing currently broken and unfinished, respectively.

Added Load Extended Command functionality to the LOAD ADDRESS V2 Protocol command handler for devices with more than 64KB of memory.

Fixed AVRISP programmer demo -- can now connect to a target and read/write Sig/Lock/Fuse/OSCCAL bytes successfully.

Changed SPI_Init() to allow for the clock polarity and data sample modes to be set.

Changed Dataflash_Init() to no longer call SPI_Init() automatically.

Moved out the handling of V2 Protocol parameters to a seperate set of files. Added parameter privellages, so that an error can be returned to the host when trying to perform a get/set value action on a parameter without the correct privellages.

Added documentation of the makefile CDEFS values to the MagStripe project.

Move AVRISP Programmer project to a new Unfinished subdirectory of Project while it is under development.

Added new Endpoint_SetEndpointDirection() macro to set the current endpoint direction for bidirectional endpoints.

Renamed internal USB_INT_ENDPOINT_SETUP macro to USB_INT_RXSTPI to fit in with the rest of the interrupt vector macros.

Rename TOTAL_NUM_CONFIGURATIONS to FIXED_NUM_CONFIGURATIONS, to match the existing FIXED_CONTROL_ENDPOINT_SIZE compile time option. Add FIXED_NUM_CONFIGURATIONS to the descriptors of each project using the option.

Change project makefiles so that the current target settings and not just the board selection is printed during the build process.

Fix warning in AudioOutput demos when AUDIO_OUT_STEREO output mode is selected.

Added new TOTAL_NUM_CONFIGURATIONS option, removed USE_SINGLE_DEVICE_CONFIGURATION compile time option (but silently convert it to USE_SINGLE_DEVICE_CONFIGURATION internally for compatibility).

Added new USE_FLASH_DESCRIPTORS compile time option. By default, descriptors can now lie in mixed memory spaces (specified by a new parameter to the CALLBACK_USB_GetDescriptor() function) unless one of the USE_*_DESCRIPTORS compile time option is specified.

Seperated out Lib components of the incomplete BluetoothHost demo application out into a seperate Lib subfolder.

Changed F_CLOCK entries in project makefiles to alias to F_CPU by default, as this is the most common case.

Fix makefiles -- the auto-addition of -D switches to each LUFA compile time option was faulty, due to GNUMake becomming confused by the spaces in the USE_STATIC_OPTIONS lines. Make user add in the switches explicitly instead.

Move new Class Driver powered demos to a new ClassDriver subdirectory, re-add old low level demos to a LowLevel subdirectory.

Commit of new class abstraction APIs for all device demos other than the MIDI demo - not documented yet.

Removed scheduler and memory allocation libraries.

Added new EVENT_USB_StartOfFrame event in the library to indicate the start of each USB frame (when generated).

Removed Tx interrupt from the USBtoSerial demo; now sends characters via polling to ensure more time for the Rx interrupt.

Deleted StdDescriptors.c, renamed USB_GetDescriptor() to CALLBACK_USB_GetDescriptor, moved ConfigDescriptor.c/.h from the LUFA/Drivers/USB/Class/ directory to LUFA/Drivers/USB/HighLevel/ in preperation for the new USB class APIs.

Fixed incorrect ENDPOINT_EPNUM_MASK mask preventing endpoints above EP3 from being selected (thanks to Jonathan Oakley).

Removed STREAM_CALLBACK() macro - callbacks now use regular function definitions to clarify user code.

Removed DESCRIPTOR_COMPARATOR() macro - comparators should now use regular function definitions to clarify user code.