Move out Bluetooth stack callback functions to a seperate BluetoothEvents.c/.h set of files for clarity in the Incomplete BluetoothHost demo. Add a new stack callback for opened ACL channels, make the demo save the RFCOMM channel when opened so that it does not have to search for it on each iteration of the main program loop.

Added new Drivers/USB/LowLevel/Device.c file to house Device mode specific functions that are more complicated than simple macros. Moved USB_Device_SendRemoteWakeup() to the new Device.c source file and corrected it to unfreeze and restart the USB controller clock before issuing a Remote Wakeup request.

Removed the USB_Device_IsRemoteWakeupSent() and USB_Device_IsUSBSuspended() macros, as they are now obsolete.

Make loops in AVRISP-MKII Clone project's XPROG protocol infinite rather than looping on the timeout value, as this is already checked inside the loop anyway.

Moved calls to V2Params_UpdateParamValues() out of the main AVRISP-MKII and XPLAINBridge project loops and into the AVRISP management function.

Spell check code and manual pages. Remove custom Doxygen CSS stylesheet, as the new 1.7 Doxygen's default stylesheet is much better.

Reduce the size of the attribute search list from 15 ranges to 8 to save RAM.

Added new VTARGET_REF_VOLTS and VTARGET_SCALE_FACTOR compile time defines to the AVRISP-MKII programmer project to set the VTARGET reference voltage and scale factor.

Fixed XPLAINBridge project not correctly reading the XMEGA's supply voltage when reporting back to the host.

The EEPROM stream read/write functions now use eeprom_update_byte() instead of eeprom_write_byte(), so that only changed bytes are written to EEPROM to preserve its lifespan.

Changed over the AVRISP-MKII and TemperatureDataLogger projects to use eeprom_update_byte() when writing non-volatile parameters to EEPROM to preserve its lifespan.

The RingBuff library code has been replaced in the XPLAINBridge project with an ultra lightweight buffer to help  improve the reliability of the bridge.

Short UUIDs are measured in bytes, not bits -- update Service Discovery Protocol code so that it can now correctly match against UUIDs in the service table.

Fixed AVRISP project not sending a full erase-and-write EEPROM command to XMEGA targets when writing to the EEPROM instead of the split write-only command (thanks to Tim Margush).

Fixed AVRISP project sending a LOAD EXTENDED ADDRESS command to 128KB AVRs after programming or reading from the last page of FLASH.

Remove incorrect check for the current device state in the Set Configuration request handler of DevChapter9, which broke Set Configuration requests to the device under most circumstances.

Move out the SPI prescaler list to a PROGMEM module-level variable in ISPTarget.c.

Fixed AVRISP-MKII clone project not correctly issuing SET EXTENDED ADDRESS commands when the extended address boundary is crossed during programming or readback (thanks to Gerard Sexton).

Fixed warnings when building the AVRISP-MKII clone project with the ENABLE_XPROG_PROTOCOL compile time option disabled.

The LIBUSB_FILTERDRV_COMPAT compile time option in the XPLAINBridge and AVRISP-MKII projects has been renamed LIBUSB_DRIVER_COMPAT, as it applies to all software on all platforms using the libUSB driver.

Fix Benito makefile which was accidentally changed during testing.

Add svn:eol-style property to source files, so that the line endings are correctly converted to the target system's native end of line style.

Change over instances of "make" in the makefiles to "$(MAKE)" to allow for the make tool to be overridden.

Removed software PDI/TPI emulation from the AVRISP-MKII clone project, as it was very buggy. PDI and TPI must now be implemented via seperate headers instead of the one unified ISP/TPI/PDI header.

Fixed Set Configuration requests not being stalled until the host has set the device's address.

Fixed possibility of internal signature retrieval being corrupted if an interrupt occurs during a signature byte read (thanks to Andrei Krainev).

Added new ENDPOINT_*_BusSuspended error code to the Endpoint function, so that the stream functions early-abort if the bus is suspended before or during a transfer.

Switch back to C based timeout ISR in the AVRISP project - assembly version was failing, and only one or two cycles could be shaved off the compiler generated code.

Change AVRISP project's timeout to be interrupt based again, but make the interrupt itself interruptable and use a seperate assembly file to hand-optimize the ISR code.

Removed the cast to uint16_t on the set baud rate in the USBtoSerial project, so that the higher >1M baud rates can be selected (thanks to Steffan).

Make sure that long reads are aborted early if the connection times out while waiting on more bytes in the AVRISP MKII clone project.

Make sure that the NVM bus/controller busy waits in the AVRISP MKII clone project abort properly if a timeout occurs while waiting for a response.

Relocate USBInterrupt.c/.h from the HighLevel USB driver directory to the LowLevel directory as it is hardware-dependent.

USB_Init() no longer calls sei() to enable global interrupts - this must now be done in the user application once all init code has run.

Make AVRISP-MKII clone project's software PDI/TPI mode more robust by keeping track of timeouts while waiting for a Tx/Rx to finish.

Added new HCI states to properly initialize the bluetooth dongle and retrieve the local BDADDR.

Factored out Bluetooth state information into a new state structure for easy reference in the user application.

Added new StackInitialized() Bluetooth stack callback function.

Ensure that the AVRISP-MKII project's Windows avrdude compatibility define is named properly in all parts of the code.

Add user callback function to the Bluetooth host demo to filter out connections from remote devices. Add in ability to reject connections based on their bluetooth device address.

Clean up RelayBoard project code.

Make AVRISP project clear the XMEGA target's reset register twice; this does not appear to take affect properly the first time under some circumstances.

Added WIN_LIBUSB_COMPAT compile time option to the AVRISP programmer project to make the code compatible with Windows builds of avrdude at the expense of AVRStudio compatibility.