Short UUIDs are measured in bytes, not bits -- update Service Discovery Protocol code so that it can now correctly match against UUIDs in the service table.

Renamed CDC device class demos' ManagementEndpoint descriptor to NotificationEndpoint to more accurately indicate its purpose.

Fixed AVRISP project not sending a full erase-and-write EEPROM command to XMEGA targets when writing to the EEPROM instead of the split write-only command (thanks to Tim Margush).

Fixed AVRISP project sending a LOAD EXTENDED ADDRESS command to 128KB AVRs after programming or reading from the last page of FLASH.

Remove incorrect check for the current device state in the Set Configuration request handler of DevChapter9, which broke Set Configuration requests to the device under most circumstances.

Move out the SPI prescaler list to a PROGMEM module-level variable in ISPTarget.c.

Fixed AVRISP-MKII clone project not correctly issuing SET EXTENDED ADDRESS commands when the extended address boundary is crossed during programming or readback (thanks to Gerard Sexton).

Fixed warnings when building the AVRISP-MKII clone project with the ENABLE_XPROG_PROTOCOL compile time option disabled.

The LIBUSB_FILTERDRV_COMPAT compile time option in the XPLAINBridge and AVRISP-MKII projects has been renamed LIBUSB_DRIVER_COMPAT, as it applies to all software on all platforms using the libUSB driver.

Fix Benito makefile which was accidentally changed during testing.

Add new ReportType parameter to the HID class driver device callback and host report sending routines.

Renamed internal Host mode Class driver descriptor comparator callback routines so that they all start with a uniform DCOMP_{Class Abbreviation}_ prefix.

Add svn:eol-style property to source files, so that the line endings are correctly converted to the target system's native end of line style.

Change over instances of "make" in the makefiles to "$(MAKE)" to allow for the make tool to be overridden.

Don't cast the line encoding baud rate to a uint16_t before performing the baud rate calculation in the Benito project.

Remove incorrect Abstract Call Management class specific descriptor from the CDC demos, bootloaders and projects.

Removed software PDI/TPI emulation from the AVRISP-MKII clone project, as it was very buggy. PDI and TPI must now be implemented via seperate headers instead of the one unified ISP/TPI/PDI header.

Fixed Set Configuration requests not being stalled until the host has set the device's address.

Fixed possibility of internal signature retrieval being corrupted if an interrupt occurs during a signature byte read (thanks to Andrei Krainev).

Added new ENDPOINT_*_BusSuspended error code to the Endpoint function, so that the stream functions early-abort if the bus is suspended before or during a transfer.

Switch back to C based timeout ISR in the AVRISP project - assembly version was failing, and only one or two cycles could be shaved off the compiler generated code.

Change AVRISP project's timeout to be interrupt based again, but make the interrupt itself interruptable and use a seperate assembly file to hand-optimize the ISR code.

Removed the cast to uint16_t on the set baud rate in the USBtoSerial project, so that the higher >1M baud rates can be selected (thanks to Steffan).

Make sure that long reads are aborted early if the connection times out while waiting on more bytes in the AVRISP MKII clone project.

Make sure that the NVM bus/controller busy waits in the AVRISP MKII clone project abort properly if a timeout occurs while waiting for a response.

Relocate USBInterrupt.c/.h from the HighLevel USB driver directory to the LowLevel directory as it is hardware-dependent.

USB_Init() no longer calls sei() to enable global interrupts - this must now be done in the user application once all init code has run.

Make AVRISP-MKII clone project's software PDI/TPI mode more robust by keeping track of timeouts while waiting for a Tx/Rx to finish.

Added new HCI states to properly initialize the bluetooth dongle and retrieve the local BDADDR.

Factored out Bluetooth state information into a new state structure for easy reference in the user application.

Added new StackInitialized() Bluetooth stack callback function.

Fixed Set/Clear Feature requests directed to a non-configured endpoint not returning a stall to the host.

Make TeensyHID bootloader use an 8 byte control endpoint to match the official Teensy, just in case Paul decides to authenticate on that attribute in the future.

Document the Bluetooth ACL layer. Remove unneeded parameters from the signalling command processing routines.

Change over the code so that the bluetooth packet data is read in by the stack rather than the user application, to make it more unform for sending/receiving, and so the library can handle incomming fragmentation in the future.

Start Service Discovery Protocol decoding and processing.

Ensure that the AVRISP-MKII project's Windows avrdude compatibility define is named properly in all parts of the code.

Add user callback function to the Bluetooth host demo to filter out connections from remote devices. Add in ability to reject connections based on their bluetooth device address.

Clean up RelayBoard project code.

Make AVRISP project clear the XMEGA target's reset register twice; this does not appear to take affect properly the first time under some circumstances.

Remove unused macro in the host mode demos for the maximum Configuration Descriptor size.

Added WIN_LIBUSB_COMPAT compile time option to the AVRISP programmer project to make the code compatible with Windows builds of avrdude at the expense of AVRStudio compatibility.

All Class Driver Host mode demos now correctly set the board LEDs to READY once the enumeration process has completed.

Fixed Still Image Host class driver not resetting the transaction ID when a new session is opened, fixed driver not sending a valid session ID to the device.

Added hardware board driver support for the PJRC Teensy line of USB AVR boards.